Veröffentlichungen der Arbeitsgruppe Produktionstechnik
2023
- Koch, P.; Rawal, P.; Töpfer, N.; Haß, T.; Böhlmann, C.; Hintze, W.:
Modular lightweight robot system for aircraft production using a generic OPC UA skill concept
in: Production Engineering 17 (2023), p. 329-339, Springer Berlin Heidelberg.
available online 15 March 2023
DOI: 10.1007/s11740-023-01183-w
2022
- Rana, P.; Hintze, W.; Schall, T.; Polley, W.:
Implementation of MC-SPG particle method in the simulation of orthogonal turning process
in: M. Liewald, A. Verl, T. Bauernhansl, H.-C. Möhring: Production at the Leading Edge of Technology, Proceedings of the 12th Congress of the German Academic Association for Production Technology (WGP), University of Stuttgart, October 2022, Springer Verlag Berlin, 2022, DOI: 10.1007/978-3-031-18318-8_37
- Hintze, W.; Brouschkin, A.; Köttner, L.; Bluehm, M.:
Model Based Prediction of Force and Roughness Extrema Inherent in Machining of Fibre Reinforced Plastics Using Data Merging
in: M. Liewald, A. Verl, T. Bauernhansl, H.-C. Möhring: Production at the Leading Edge of Technology, Proceedings of the 12th Congress of the German Academic Association for Production Technology (WGP), University of Stuttgart, October 2022, Springer Verlag Berlin, 2022, DOI: 10.1007/978-3-031-18318-8_5
- Romanenko, D.; Jothi Prakash, V.; Kuhn, T.; Moeller, C.; Hintze, W.; Emmelmann, C.:
Effect of DED process parameters on distortion and residual stress state of additively manufactured Ti-6Al-4V components during machining
in: Proceedings of the 12th CIRP Conference on Photonic Technologies (LANE 2022), Fuerth, Germany, Procedia CIRP 111 (2022) 271-276, DOI: 10.1016/j.procir.2022.08.020
- Hintze W.; Möller C.; Ploog P.; Bobzin K.; Kalscheuer C.; Carlet M.; Stachowski N.
Influence of self-lubricating tool coatings on cutting temperature and coefficient of friction during turning of Ti6Al4V
in: Proceedings of the 20th Plansee Seminar, International Conference on Refractory Metals and Hard Materials, May 30 – June 3, 2022, Reutte/Austria
- Hintze W.; Hinrichs M; Rosenthal O.; Schleinkofer U.; Venturini R.;
Tuned mass dampers for boring bars with small diameter
in: Proceedings of the 20th Plansee Seminar, International Conference on Refractory Metals and Hard Materials, May 30 – June 3, 2022, Reutte/Austria
- Hintze, W.; Romanenko, D.; Molkentin, L.; Koettner, L.; Mehnen, J.:
Holistic process monitoring with machine learning classification methods using internal machine sensors for semi-automatic drilling
in: Proceedings of the 55th CIRP Conference on Manufacturing Systems (CMS 2022), Lugano, Switzerland, Procedia CIRP 107 (2022) 972-977, DOI: 10.1016/j.procir.2022.08.020
- Brillinger, C.; Kallipalayam Murugesan, S.K.; Moeller, C.; Boehlmann, C.; Hintze, W.; Niermann, D.:
Accuracy Analysis for a Flow Line Process using a Mobile Holding Fixture for Machining CFRP Components
SAE Technical Paper 2022-01-0041, ISSN 0148-7191
available online 08. März 2022, DOI: 10.4271/2022-01-0041
- Breitzke, A.; Hintze, W.:
Workshop-suited geometric errors identification of three-axis machine tools using on-machine measurement for long term precision assurance
in: Precision Engineering (2022), ISSN 0141-6369
available online 20. Februar 2022, DOI: 10.1016/j.precisioneng.2022.02.006
- Lissek, F.; Kaufeld, M.; Bergmann, J.P.; Hintze, W.:
Eine Frage des Timings – Schädigungsfreies Bohren nachgiebiger CFK-Strukturen
in: Werkstatt+Betrieb, 17.02.2022.
Online veröffentlicht unter https://www.werkstatt-betrieb.de/a/article-358589
- Hintze, W.; Köttner, L.; Brouschkin, A.; Blühm, M.; Jakele, L.:
A General Unique Description of Cutting Direction and Engagement for Arbitrary Oblique Cutting of Orthotropic Materials – Modeling and Validation for Grinding of Unidirectional CFRP
Technical Report, CIRP Winter Meetings, STC C - Cutting, Paris, 2022-02-17
2021
- Bobzin, K.; Brögelmann, T.; Carlet, M.; Stachowski, N.; Hintze, W.; Möller, C.; Ploog, P.:
Self-lubricating CrAlVN coatings for turning of Ti6Al4V: oxidation and wear behavior
Material Science & Engineering Technology (Wiley) Dezember 2021, Volume 52, Issue 12, S. 1394-1412, DOI: 10.1002/mawe.202100042
- Hintze, W.; Köttner, L.:
Curved Circular Cutting of lightweight Structures
China-Germany-Japan Workshop on Advanced Manufacturing of New Energy Vehicles, 08.–10. Dezember 2021, Composites United e.V.,Virtual Workshop
- Bobzin, K.; Kalscheuer, C.; Carlet, M.; Stachowski, N.; Hintze, W.; Möller, C.; Ploog, P.:
Wear development of self-lubricating CrAlVN coatings during turning Ti6Al4V
in: Denkena, B. (Hrsg.): Procedia Manufacturing of the 21st Machining Innovations Conference for Aerospace Industry 2021 (MIC 2021), Hannover, Volume 21 (2021) S. 70-77, SSRN
available online 17. November 2021, DOI: 10.2139/ssrn.3947799
- Hintze, W.; Möller, C.; Romanenko, D.; Junghans, S.:
Adaptive Präzisionsbearbeitung additiv gefertigter Leichtbaustrukturen in der digitalisierten Prozesskette
in: Unter Span - Magazin des Manufacturing Innovations Network (2021), S. 42-43, ISSN 2365-7006
- Mehnen, J.; Hintze, W.; Köppe, M.:
Influence of contour radius and fiber orientation on heat accumulation during machining of unidirectional CFRP
in: MM Science Journal 2021-11-01, Proceeding of 16th International Conference on High Speed Machining (HSM 2021), 26–27 Oktober 2021, Darmstadt, ISSN 1803-1269, S. 5085-5092, DOI: 10.17973/MMSJ.2021_11_2021156
- Rana, P.; Hintze, W.; Schall, T.; Polley, W.:
Study on the Influence of the Coating Thickness in Turning of a Hard to Machine Material Using FEM-Simulation
in: Behrens, B.-A.; Brosius, A.; Drossel, W.-G.; Hintze, W.; Ihlenfeldt, S.; Nyhuis, P. (Eds.): Production at the leading edge of technology, Proceedings of the 11th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 29 - September 30, Springer-Verlag, Berlin, 2021, S. 256-264, ISBN 978-3-030-78424-9, DOI: 10.1007/978-3-030-78424-9_29
- Schulze, B.; Rawal, P.; Kothe, S.; Hintze, W.:
Subsequent Synchronization of Individual Monitoring Systems for Machining of Aircraft Structures via a Data Collector Using OPC UA
in: Behrens, B.-A.; Brosius, A.; Drossel, W.-G.; Hintze, W.; Ihlenfeldt, S.; Nyhuis, P. (Eds.): Production at the leading edge of technology, Proceedings of the 11th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 29 - September 30, Springer-Verlag, Berlin, 2021, S. 292-300, ISBN 978-3-030-78424-9, DOI: 10.1007/978-3-030-78424-9_33
- Möller, C.; Hintze, W.; von Wenserski, R.:
Impact Separation of Support Structures from Laser Powder Bed Fusion Generated LPBF Parts
in: Behrens, B.-A.; Brosius, A.; Drossel, W.-G.; Hintze, W.; Ihlenfeldt, S.; Nyhuis, P. (Eds.): Production at the leading edge of technology, Proceedings of the 11th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 29 - September 30, Springer-Verlag, Berlin, 2021, S. 384-391, ISBN 978-3-030-78424-9, DOI: 10.1007/978-3-030-78424-9_43
- Behrens, B.-A.; Brosius, A.; Drossel, W.-G.; Hintze, W.; Ihlenfeldt, S.; Nyhuis, P (Eds.):
Production at the leading edge of technology
Proceedings of the 11th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 28 - September 29, Springer-Verlag, Berlin, 2021, ISBN 978-3-030-78423-2, ISBN 978-3-030-78424-9 (eBook)
- Hintze, W.:
CFK-Bearbeitung. Trenntechnologien für Faserverbundkunststoffe und den hybriden Leichtbau
Springer Vieweg, Berlin. ISBN 978-3-662-63264-2, ISBN 978-3-662-63265-9 (eBook), DOI: 10.1007/978-3-662-63265-9
- Hintze, W.; Mehnen, J.; Köttner , L.; Romanenko, D.:
Bohrprozess im Griff - Halbautomatisches Bohren wird jetzt mit KI überwachbar
in: MM MaschinenMarkt, (2021) 7, S. 50ff.
Online veröffentlicht unter
https://www.maschinenmarkt.vogel.de/halbautomatisches-bohren-wird-jetzt-mit-ki-ueberwachbar-a-1048320/
- von Wenserski, R.:
Helixfräsen und Bohren von laseradditiv gefertigten Bauteilen aus Titan für Luftfahrtanwendungen
Dissertation, erschienen in: Lödding, H.; Hintze, W.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 47, Hamburg 2021, ISSN 1613-8244, DOI: 10.15480/882.3723
- Mehnen, J.; Hintze, W.:
Prozessüberwachung durch Machine Learning beim semi-automatischen Nietbohren in der Luftfahrtindustrie
METAV-Digital 2021 Websession im Bereich "Intelligente Produktion", Vortrag, 08. April 2021, Zur Aufzeichnung
- Möller, C.; Dege, J. H.; Heuwinkel, M.:
Entwicklung eines tangentialen Walzenstirnfräskonzeptes für Titanstrukturbauteile
Hanser Tagungen "Schwer zerspanbare Werkstoffe in der industriellen Praxis", Vortrag, Digitales Event, 02.-03. März 2021
- Hintze, W.; Rosenthal, O.; Hinrichs, M.; Steinbach, S.:
Zerspanung von gesintertem Hartmetall - Grundlagen und Anwendung
Hanser Tagungen "Schwer zerspanbare Werkstoffe in der industriellen Praxis", Vortrag, Digitales Event, 02.-03. März 2021
2020
- Hintze, W.; Ploog, P.; Bluehm, M.; Möller, C.:
Development of a process-oriented tribological test rig for the performance assessment of tool coatings in turning of titanium Ti6Al4V
in: Denkena, B. (Hrsg.): Procedia Manufacturing of the 20th Machining Innovations Conference for Aerospace Industry - MIC 2020, Hannover, Volume 20 (2020) S. 107-115, SSRN
available online 03 November 2020 doi.org/10.2139/ssrn.3724119
- Hintze, W.; Rosenthal, O.; Möller, C.:
Was die Stabilität von Werkzeugspannmitteln beeinflusst
in: VDW-Branchenreport September 2020
- Kothe, S.; Diehl, B.; Niermann, D.; Chen, M.; Wolf, M.; Hintze, W.:
Automated Assembly of Thermoplastic Fuselage Structures for Future Aircrafts
in: Behrens, B.-A.; Brosius, A.; Hintze, W.; Ihlenfeldt, S.; Wulfsberg, J. P. (Eds.): Production at the leading edge of technology, Proceedings of the 10th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 23 - September 24, Springer-Verlag, Berlin, 2020, S. 467-475, ISBN 978-3-662-62137-0, DOI: 10.1007/978-3-662-62138-7_47
- Köttner, L.; Mehnen, J.; Romanenko, D.; Bender, S.; Hintze, W.:
Process monitoring using machine learning for semi-automatic drilling of rivet holes in the aerospace industry
in: Behrens, B.-A.; Brosius, A.; Hintze, W.; Ihlenfeldt, S.; Wulfsberg, J. P. (Eds.): Production at the leading edge of technology, Proceedings of the 10th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 23 - September 24, Springer-Verlag, Berlin, 2020, S. 497-507, ISBN 978-3-662-62137-0, DOI: 10.1007/978-3-662-62138-7_50
- Behrens, B.-A.; Brosius, A.; Hintze, W.; Ihlenfeldt, S.; Wulfsberg, J. P. (Eds.):
Production at the leading edge of technology
Proceedings of the 10th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 23 - September 24, Springer-Verlag, Berlin, 2020, ISBN 978-3-662-62137-0
- Hintze, W.; Mehnen, J.; Schmid, M.; Süess, B.; Weigand, M.:
Alle Parameter genau abgestimmt – Hochleistungs-CFK-Bearbeitung mit diamantbeschichteten Bohr- und Fräswerkzeugen
in: Diamond Business, 03. September 2020
- Brieskorn, L.; Hintze, W.:
Automated removal of carbon fiber reinforced plastic layers for the repair by adhesive bonding
in: Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering, 234(13) 2011–2022
available online 5 August 2020
doi.org/10.1177/954410020947913
- Hintze, W.; von Wenserski, R.; Junghans, S.; Möller, C.:
Finish machining of Ti6Al4V SLM components under consideration of thin walls and support structure removal
in: Procedia Manufacturing, Volume 48, 2020, p. 485-491.
available online 23 June 2020
doi.org/10.1016/j.promfg.2020.05.072
- Möller, Chr.:
Entwicklung eines hochgenauen Bearbeitungsroboters durch den Einsatz zusätzlicher Messtechnik
Dissertation, erschienen in: Hintze, W.; Mayer, B.; Wollnack, J.; Niermann, D. (Hrsg.): Forschung für die Produktionstechnik von Morgen, Band 4, Fraunhofer IFAM, Stade, Fraunhofer Verlag, Stuttgart, 2020, ISBN 978-3-8396-1600-0
- Hintze, W.; Rosenthal, O.; Möller, C.:
Tool holder influence in roughing with end mills
Technical Report, CIRP Winter Meetings, STC-M Machines, Paris, 2020-02-21
- Rosenthal, O.; Hintze, W.; Möller, C.:
Assessment of tool holder performance in roughing with end mills
Process dynamics and surface formation
In: Production Engineering 14 (2020), p. 253–263, Springer Berlin Heidelberg.
available online 08 January 2020
doi.org/10.1007/s11740-019-00944-w
The lists of publications are available in German only:
2019
- Rawal, P.; Brillinger, C.; Böhlmann, C.; Hintze, W.:
Sensor based online quality monitoring system for detection of milling defects on CFRP structures
in: CEAS Aeronautical Journal (2019)
available online 21 December 2019 doi.org/10.1007/s13272-019-00436-8
Springer Link s13272-019-00436-8
- Maiß, O.; Bluehm, M.; Ploog, P.; Hintze, W.:
Straightening of thin-walled titanium components by defined deep rolling
LightMAT - 3rd Conference & Exhibition on Light Materials – Science and Technology, Manchester, UK, 04.11.2019
- Mehnen, J.; Hintze, W.; Köttner, L.; von Wenserski, R.:
Temperature field due to a moving heat source in machining orthotropic composites with arbitrary fiber orientation
in: Proceedings of the 2nd CIRP Conference on Composite Material Parts Manufacturing (CCMPM 2019), Sheffield, United Kingdom, Procedia CIRP 85 (2019): 2-7, 2019 doi.org/10.1016/j.procir.2019.09.019
- Rana, P.; Hintze, W.; Zielasko, W.; Schuster, T.:
Orthogonal Turning Simulations for Casted Steel Alloy Using Mesh Free Methods
in: Wulfsberg, J. P.; Hintze, W.; Behrens, B.-A. (Eds.): Production at the leading edge of technology, Proceedings of the 9th Congress of the German Academic Association for Production Technology (WGP), Hamburg, September 30 - October 2, Springer Vieweg Verlag, 2019, S. 337-346, ISBN 978-3-662-60417-5
- Wulfsberg, J. P.; Hintze, W.; Behrens, B.-A. (Eds.):
Production at the leading edge of technology
Proceedings of the 9th Congress of the German Academic Association for Production Technology (WGP), Hamburg, September 30 - October 2, Springer Vieweg Verlag, 2019, ISBN 978-3-662-60417-5
- Cordes, M.:
Modellierung von Bahngenauigkeit und dynamischer Stabilität beim robotergeführten Fräsen
Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Band 39, Hamburg, 2019, ISSN 1613-8244
- Susemihl, H.:
Mobile Robotersysteme zur Zerspanung von Großstrukturen in der Flugzeugproduktion
Dissertation, erschienen in: Hintze, W.; Mayer, B.; Wollnack, J.; Niermann, D. (Hrsg.): Forschung für die Produktionstechnik von Morgen, Band 3, Fraunhofer IFAM, Stade, Fraunhofer Verlag, Stuttgart, 2019, ISBN 978-3-8396-1440-2
- Hintze, W.; von Wenserski, R.; Möller, C.:
Assessment of support structures with regard to their machinability in simultaneous precision machining of SLS Ti6Al4V parts
Technical Report, CIRP Winter Meetings, Collaborative Working-Group on Additive Manufacturing, Paris, 2019-02-20
- Schulze, B.; Koch, P.; Bonas, J.; Bense, R.; Borrmann, C.; Hintze, W.:
Industrial Approaches to Realize a Digital Production in Aviation Industry
in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 7th International Workshop on Aircraft System Technologies (AST 2019), February 19 - 20, 2019, Hamburg, Germany
Reihe: Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2019, S. 245-254, ISBN 978-3-8440-6470-4
- Hintze, W.; Lödding, H.; Friedewald, A.; Mehnen, J.; Romanenko, D.; Möller, C.; Brillinger, C.; Sikorra, J.:
Digital Assistance Systems for Smart Drilling Units in Aircraft Structural Assembly
in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 7th International Workshop on Aircraft System Technologies (AST 2019), February 19 - 20, 2019, Hamburg, Germany
Reihe: Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2019, S. 255-266, ISBN 978-3-8440-6470-4
- Brillinger, C.; Susemihl, H.; Ehmke, F.; Staude, T.; Deutmarg, K.; Klemstein, M.; Böhlmann, C.; Hintze, W.; Wollnack, J.:
Mobile Laser Trackers for Aircraft Manufacturing: Increasing Accuracy and Productivity of Robotic Applications for Large Parts
in: SAE Technical Papers 2019-03-19, ISSN 0096-5170, DOI:10.4271/2019-01-1368
- Hintze, W.; Lödding, H.; Friedewald, A.; Mehnen, J.; Romanenko, D.; Sikorra, J.:
Digitalisierte Bohrtechnologie für die Strukturmontage
Digitised Drilling Technology for the Structure Assembly
in: CFK-Valley Stade e.V. (Hrsg.): INNOVATION REPORT, 1-2019, S. 46-47
INNOVATION REPORT, Ausgabe 1-2019 (PDF-Datei, Seite 46)
2018
- Hintze, W.; Blühm, M.; Ploog, P.:
Laser-Scored-Machining steigert Qualität und reduziert Werkzeugkosten beim Besäumen von Faserverbundbauteilen
in: Unter Span - Magazin des Machining Innovations Network (2018), S. 20-21
- Hintze, W.; Schötz*, R.; Mehnen, J.; Köttner, L.; Möller, C.:
Helical milling of bore holes in Ti6Al4V parts produced by selective laser melting with simultaneous support structure removal
in: Denkena, B. (Hrsg.): Procedia Manufacturing of the 18th Machining Innovations Conference for Aerospace Industry - MIC 2018, Hannover, Volume 18 (2018) S. 89-96, Elsevier
available online 13 December 2018 doi.org/10.1016/j.promfg.2018.11.012
- Hintze, W.; Korves, L.; Blühm, M.; Ploog, P.; Müller, M.:
Laser Scored Machining - Prozesssichere Fräsbearbeitung von CFK-Komponenten für die Luftfahrtindustrie
8. IfW-Tagung Bearbeitung von Verbundwerkstoffen, Stuttgart, 29.11.2018
- Hintze, W.; von Wenserski, R.:
IPMT entwickelt Strategien für die spanende Nachbearbeitung additiver Bauteile
in: Hanse-Aerospace Bulletin, 03/2018, S.20-21
- Hintze, W.; Steinbach, S.:
Grundlagen der Zerspanung von gesintertem Hartmetall
Seminar "Hartmetall Fräsen", Vortrag, Soltau, 26.09.2018
- Rawal, P.; Brillinger, C.; Böhlmann, C.; Hintze, W.:
Sensor based online quality monitoring system for detection of milling defects on CFRP structures
(Sensorbasiertes Online-Qualitätsüberwachungssystem zur Detektion von Schäden an CFK-Fräskanten)
Deutscher Luft- und Raumfahrtkongress 2018 "Luft- und Raumfahrt – Digitalisierung und Vernetzung", Vortrag, Friedrichshafen, 5. September 2018
- Cordes, M.; Hintze, W.; Altintas, Y.:
Chatter stability in robotic milling
In: Robotics and Computer-Integrated Manufacturing 55 (2019), p. 11–18, Elsevier
available online 26 July 2018 doi:10.1016/j.rcim.2018.07.004
- Brügmann, F.:
Bauteilqualität und Werkzeugverschleiß beim Fräsen von CFK-Gelege unter räumlichen Eingriffsbedingungen
Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Band 36, Hamburg, 2018, ISSN 1613-8244
- Kothe, S. M.:
Spanende Bearbeitung von Faserverbundstrukturen mit Industrierobotern für die Luftfahrt
Dissertation, erschienen in: Hintze, W.; Mayer, B.; Wollnack, J.; Niermann, D. (Hrsg.): Forschung für die Produktionstechnik von Morgen, Band 1, Fraunhofer IFAM, Stade, Fraunhofer Verlag, Stuttgart, 2018, ISBN 978-3-8396-1278-1
- Hintze, W.; Brügmann, F.; Cordes, M.; Boll, B.:
Modeling of Tool Wear in Full Cut Milling of Unidirectional CFRP with Tungsten Carbide
Technical Report, CIRP Winter Meetings, CWG Composite Materials Part Manufacturing, Paris, 2018-02-22
- Hintze, W.; Clausen, R.; Schütte, C.; Kroll, K.:
Evaluation of the Total Cutting Force in Drilling of CFRP - A Novel Experimental Method for the Analysis of the Cutting Mechanism
Production Engineering (2018), DOI 10.1007/s11740-018-0807-2
- Hintze, W.; Steinbach, S.:
Grundlagen der Zerspanung von gesintertem Hartmetall
Seminar "Hartmetall Fräsen", Vortrag, Soltau, 07.02.2018
- Proes, F.; Eichenseer, C.; Hintze, W.; Schell, N.; Leahy, W.; M'Saoubi, R.; Sattel, S.:
In situ analysis of PCBN cutting tool materials during thermo-mechanical loading using synchrotron radiation
Production Engineering (2018), DOI 10.1007/s11740-018-0791-6
- Hintze, W.; Steinbach, S.; Susemihl, C.; Kähler, F.:
HPC-milling of WC-Co cemented carbides with PCD
International Journal of Refractory Metals and Hard Materials, Elsevier, 2018
available online 18 December 2017 doi:10.1016/j.ijrmhm.2017.12.019
2017
- Möller, C.; Schmidt, H.; Koch, P.; Böhlmann, C.; Kothe, S.; Wollnack, J.; Hintze, W.:
Machining of large scaled CFRP-Parts with mobile CNC-based robotic system in aerospace industry
in: Denkena, B. (Hrsg.): Procedia Manufacturing of the 17th Machining Innovations Conference for Aerospace Industry - MIC 2017, Hannover, Volume 14 (2017) S. 17-29, Elsevier
available online 05 December 2017 doi:10.1016/j.promfg.2017.11.003
- Susemihl, H.; Brillinger, C.; Stürmer, S.; Hansen, S.; Böhlmann, C.; Kothe, S.; Wollnack, J.; Hintze, W.:
Referencing Strategies for High Accuracy Machining of Large Aircraft Components with Mobile Robotic Systems
SAE Technical Paper 2017-01-2166, 2017
- Möller, C.; Schmidt, H.; Koch, P.; Böhlmann, C.; Kothe, S.; Wollnack, J.; Hintze, W.:
Real Time Pose Control of an Industrial Robotic System for Machining of Large Scale Components in Aerospace Industry Using Laser Tracker System
SAE Int. J. Aerosp. 10(2):100-108, 2017
- Hintze, W.; Brügmann, F.:
Influence of spatial tool inclination on delamination when milling CFRP
Journal of Materials Processing Technology
available online 26 October 2017 doi:10.1016/j.jmatprotec.2017.10.041
- Hintze, W.; Köttner, L.:
Curved Circular Cutting - Innovative Trennschleiftechnologie rationalisiert das Besäumen von FVK-Schalenbauteilen
Composites Europe 2017, Vortrag, Stuttgart, 21.09.2017
- Kothe, S.; Koch, P.; von Stürmer, S. P.; Böhlmann, C.; Hintze, W.:
Die Roboter kommen. Roboterbasierte Zerspanungssysteme ergänzen die Werkzeugmaschine
in: Unter Span - Magazin des Machining Innovations Network (2017) 2, S. 16-17
- Hintze, W.; Brügmann, F.; Köttner, L.; Mehnen, J.:
Bearbeitung von FVK-Strukturen mit innovativen Technologien und Produktionssystemen
2. Bremer Faserverbundtage, Vortrag, Bremen, 31.08.-01.09.2017
- Hintze, W.; Steinbach, S.; Hertel, C.; Kähler, F.; Mai, T. N.:
Machinability and Process Performance in HPC-Milling of Sintered Tungsten Carbide
67th CIRP General Assembly, Technical Report STC C - Cutting, Lugano (Switzerland), August 25th 2017
- Hintze, W.; Möller, C.; Schötz, R.:
Spanende Nachbearbeitung additiv gefertigter Titanstrukturen der Luftfahrt
MIN Workshop "Nachbearbeitung additiv gefertigter Bauteile", Vortrag, Varel, 12./13.07.2017
- Hintze, W.; Steinbach, S.; Hertel, C.; Kähler, F.:
HPC-Milling of WC-Co cemented carbides with PCD
in: Proceedings of the 19th Plansee Seminar, International Conference on Refractory Metals and Hard Materials, May 29 – June 2, 2017, Reutte/Austria
- Hintze, W.; Klingelhöller, C.:
Analysis and Modeling of Heat Flux into the Tool in Abrasive Circular Cutting of Unidirectional CFRP
in: Procedia of the 1st CIRP Conference on Composite Materials Parts Manufacturing (CIRP CCMPM '17), June 8-9, 2017, Karlsruhe, Elsevier, Vol. 66, 2017, S. 210-214, ISSN: 2212-8271 doi:10.1016/j.procir.2017.03.305
- Hintze, W.; Brügmann, F.:
Influence of Curved Workpiece Contours on Delamination During end Milling of FRP
in: Procedia of the 10th Conference on Intelligent Computation in Manufacturing Engineering (CIRP ICME '16), July 20-22, 2016, Ischia, Italy, Elsevier, Vol. 62, 2017, S. 62-67, ISSN: 2212-8271 doi:10.1016/j.procir.2016.06.115
- Hintze, W.; Schötz, R.:
3D Druck - Ohne spanende Nachbearbeitung kein funktionsfähiges Bauteil
in: Unter Span - Das Magazin des Machining Innovations Network (2017) 1, S. 24-25
- Hintze, W.; Köttner, L.:
Trennschleifen in einer neuen Dimension - Maschinengeführte 3D Bearbeitung von CFK-Schalenbauteilen mit der Trennscheibe
Abrasive Cutting in a new dimension – machine guided 3D processing of CFRP shell components with cutting disk
in: CFK-Valley Stade e.V. (Hrsg.): INNOVATION REPORT, 1-2017, S. 30-31
INNOVATION REPORT, Ausgabe 1-2017 (PDF-Datei, Seite 30)
- Geis, T.:
Bearbeitungsstrategien zur Zerspanung von Faser-Verbund-Honeycomb-Sandwich
Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr.33, Hamburg, 2017, ISSN 1613-8244
- Hintze, W.; Brügmann, F.; Cordes, M.; Mehnen, J.:
Modellierung von Delaminationsphänomenen bei der Zerspanung langfaserverstärkter Faserverbundwerkstoffe
In: Biermann, D. (Hrsg.): Spanende Fertigung. Prozesse, Innovationen, Werkstoffe. Vulkan-Verlag, Essen, 2017, S. 65–78, ISBN 978-3-8027-2989-8
- Valencia, D.; Wollnack, J.:
Identification of the Geometrical Relationships of Sensor, Tool and Actuator Flange via Defined Machine Movements for Fully Automated Bracket Installation
in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 6th International Workshop on Aircraft System Technologies (AST 2017), February 21 - 22, 2017, Hamburg, Germany
Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2017, S. 337-346, ISBN 978-3-8440-5086-8
- Kothe, S.; von Stürmer, S. P.; Koch, P.; Böhlmann, C.; Hintze, W.:
Accuracy Analysis and Optimization of Industrial Robots for Aerospace Production
in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 6th International Workshop on Aircraft System Technologies (AST 2017), February 21 - 22, 2017, Hamburg, Germany
Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2017, S. 347-353, ISBN 978-3-8440-5086-8
- Schmick, F.; Rao, S.; Wollnack, J.:
Adaptive Robot Trajectory Planning for the Automated Bonding of Large CFRP Structures
in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 6th International Workshop on Aircraft System Technologies (AST 2017), February 21 - 22, 2017, Hamburg, Germany
Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2017, S. 355-364, ISBN 978-3-8440-5086-8
- Hintze, W.; Möller, C.; Schötz, R.:
Finish Machining of Titanium Components - Challenges of New Process Chains and Recent Alloys
in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 6th International Workshop on Aircraft System Technologies (AST 2017), February 21 - 22, 2017, Hamburg, Germany
Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2017, S. 397-407, ISBN 978-3-8440-5086-8
2016
- Hintze, W.; Brügmann, F.; Cordes, M.:
Entwicklung und Einsatzverhalten von Hartmetallwerkzeugen zum Bohren und Fräsen von Kohlenstofffaserverstärktem Kunststoff (CFK)
In: Tagungsband zu "35. Hagener Symposium Pulvermetallurgie - Zerspanung von und mit pulvermetallurgischen Werkstoffen", 24.-25. November 2016, Hagen, S. 213-230, ISBN 978-3-946537-32-8
- Hintze, W.; Rosenthal, O.:
Bearbeitungsgerechte Auswahl von Werkzeugspannsystemen für Schaftwerkzeuge
in: Unter Span - Das Magazin des Machining Innovations Network (2016) 2, S. 22
- Hintze, W.; Cordes, M.; Geis, T.; Blühm, M.; Emmelmann, C.; Canisius, M.:
Laser Scored Machining of Fiber Reinforced Plastics to Prevent Delamination
in: Denkena, B.; Aoyama, T.; Arrazola, P.-J.; Altintas, Y.; Lucca, D. A. (Hrsg.):
Procedia Manufacturing of the 16th Machining Innovations Conference for Aerospace Industry - MIC 2016, Hannover,
Volume 6 (2016) S. 1-8, Elsevier,
available online 18 November 2016, doi:10.1016/j.promfg.2016.11.001
- Susemihl, H.; Möller, C.; Kothe, S.; Schmidt, H.; Shah, N.; Brillinger, C.; Wollnack, J.; Hintze, W.:
High Accuracy Mobile Robotic System for Machining of Large Aircraft Components
SAE Int. J. Aerosp. 9(2):2016, doi:10.4271/2016-01-2139
- Kothe, S.; Stürmer, S.; Schmidt, H.; Böhlmann, C.; Wollnack, J.; Hintze, W.:
Accuracy Analysis and Error Source Identification for Optimization of Robot based Machining Systems for Aerospace Production
SAE Technical Paper 2016-01-2137, 2016, doi:10.4271/2016-01-2137
- Hintze, W.; Klingelhöller, C.; Köttner, L.:
Curved Circular Cutting of Spherical CFRP Structures - Kinematics, Tool Engagement and Edge Quality
CIRP General Assembly, Technical Report STC C, Guimaraes, Portugal, August 25th 2016
- Cordes, M.; Hintze, W.:
Offline simulation of path deviation due to joint compliance and hysteresis for robot machining
in: The International Journal of Advanced Manufacturing Technology (2017) 90, pp. 1075-1083,
available online 17 September 2016, doi:10.1007/s00170-016-9461-z
- Hintze, W.; Brügmann, F.:
Influence of curved workpiece contours on delamination during end milling of FRP
"CIRP ICME '16 - 10th CIRP Conference on Intelligent Computation in Manufacturing Engineering", Vortrag, Ischia, Italien, 20.-22.07.2016
- Böhlmann, C.; Kothe, S.; Susemihl, H.; Hintze, W.:
Produktion mobilisieren - Mobiles Robotersystem zur mechanischen Bearbeitung von Großstrukturen
in: Unter Span - Das Magazin des Machining Innovations Network (2016) 1, S. 16
- Klingelhöller, C.:
Trennschleifen von CFK-Schalenbauteilen mit räumlich gekrümmten Konturen
Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 30, Hamburg, 2016, ISSN 1613-8244
- Hintze, W.:
Bearbeitung neuer Werkstoffe
2. Expertentreffen Produktion 2020, Vortrag, Seco Tools, Erkrath, 20./21.04.2016
2015
- Griefahn, D.:
Geometrieprüfung innerer Strukturen von Faserverbund-Sandwichbauteilen
Dissertation, erschienen in: Hintze, W.; Wollnack, J.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 28, Hamburg, 2015, ISSN 1613-8244
- Hintze, W.; Steinbach, S.:
Direktzerspanung von gesintertem Hartmetall: Herausforderungen und Perspektiven
Makino Werkzeug- & Formenbauforum (Die & Mould Forum), Kirchheim unter Teck, 24. - 25. November 2015
- Hintze, W.; Klingelhöller, C.; Griefahn, D.; Geis, T.:
Faserverbundbauteile nacharbeitsfrei besäumen durch Laser-Scored-Machining (LSM)
Trimming fibre composite components without rework by Laser-Scored-Machining (LSM)
in: CFK-Valley Stade e.V. (Hrsg.): INNOVATION REPORT, 1-2015, S. 34-35
INNOVATION REPORT, Ausgabe 8, 1-2015 (PDF-Datei, Seite 34)
- Hintze, W.; Körkel, G. K.:
Zerspanbarkeit von Faserkunststoffverbunden - Neue Erkenntnisse durch Grundlagenuntersuchungen
in: Unter Span - Das Magazin des Machining Innovations Network (2015) 2, S. 25-26
- Dose, F.:
Methode zur wissensbasierten Prozessentwicklung - Ein Ansatz für die Berücksichtigung sich wandelnder Teilsysteme beim Bohren von Schichtverbunden
Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 26, Hamburg, 2015, ISSN 1613-8244
- Hintze, W.; Klingelhöller, C.:
3D-Trennschleifen zum Besäumen räumlich gekrümmter CFK-Bauteile
1st International Composites Congress, Stuttgart, 21.-22. September 2015
- Hintze, W.; Möller, C.; Steinbach, S.:
Fräsen von gesintertem Hartmetall
in: Unter Span - Das Magazin des Machining Innovations Network (2015) 1, S. 19
Unter Span 01/2015 (S. 19) - Hintze, W.; Cordes, M.; Susemihl, H.:
Stand und aktuelle Entwicklungen der Zerspanung mit Industrierobotern
MIN-Workshop Alternative Fertigungstechnologien, Varel, 24.03.2015
- Körkel, G. K.:
Zerspanbarkeitsbewertung von Faserverbundkunststoffen bei der Fräsbearbeitung dünnwandiger Bauteile in der Großserie
Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 24, Hamburg, 2015, ISSN 1613-8244
- Lay, M.; Leahy, W.; O'Malley, D.; Geis, T.; Hintze, W.:
Trimming and Slotting of Carbon Fiber Reinforced Polymer (CFRP) with PCD End Mills
in: Proceedings of INTERTECH 2015, May 19 - 20, 2015, Indianapolis, USA
- Hintze, W.:
Entwicklung und Einsatz von Präzisionswerkzeugen zum Bohren und Fräsen von CFK
6. Wernesgrüner Werkzeugsymposium, 11.-13.03.2015
- Möller, C.:
Neue Ansätze zur Präzisionsbearbeitung von Leichtbauwerkstoffen, 5. ordentliche Mitgliederversammlung "Machining Innovation Network", Vortrag, Varel, 25.02.2015
- Hintze, W.; Brügmann, F.:
Endmilling of Recent CFRP Materials with Cemented Carbide and Diamond Tools - Analysis of Process; Tool Wear and Quality
in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 5th International Workshop on Aircraft System Technologies (AST 2015), February 24 - 25, 2015, Hamburg, Germany
Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2015, S. 373-382, ISBN 978-3-8440-3319-9
- Hintze, W.; Eichenseer, C.:
Analysis of Phase-dependent Strains and Stress in Mixed Ceramics under Thermo-mechanical Load using Synchrotron Radiation
Technical Report, CIRP Winter Meetings, STC Cutting, Paris, 2015-02-19
- Eichenseer, C.; Hintze, W.; Sattel, S.:
Untersuchung des Schneidstoffverhaltens "in situ" - Innovative Messmethode detektiert Spannungen
in: VDI-Z 157(2015) 1/2, Springer-VDI-Verlag, Düsseldorf, 2015, S. 44-47
- Hintze, W.; Cordes, M.; Körkel, G.:
Influence of weave structure on delamination when milling CFRP
in: Journal of Materials Processing Technology 216 (2015), S. 199-205,
available online 21 September 2014, doi:10.1016/j.jmatprotec.2014.09.004
2014
- Hintze, W.; Klingelhöller, C.; Langhof, O.:
Curved sawing of thin lightweight components
in: Journal of Production Engineering Research and Development, available online 27 November 2014, doi:10.1007/s11740-014-0587-2
- Eichenseer, C.:
Beschichtung, thermomechanische Charakterisierung und Spannungsanalyse von Schneidkeramik
Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 22, Hamburg, 2014, ISSN 1613-8244
- Hintze, W.; Cordes, M.:
Robotergeführtes Fräsen von Leichtbauwerkstoffen
in: Unter Span - Das Magazin des Machining Innovations Network (2014) 2, S. 27
- Körkel, G.; Hintze, W.; Polley, W.; Zielasko, W.:
Machinability of fiber-reinforced plastics - An integral approach for large-scale production
in: Proceedings of the 8th International CFK-Valley Stade Convention 2014, June 24-25, 2014, Stade, Germany, S. 116-122
- Geis, T.; Klingelhöller, C.; Hintze, W.:
Constant Depth Scoring of Fibre Reinforced Plastic Structures to Prevent Delamination
in: Procedia of the 6th CIRP International Conference on High Performance Cutting (HPC2014), June 23-25, 2014, Berkeley, USA, Elsevier, Vol. 14, 2014, S. 205-210 doi:10.1016/j.procir.2014.03.103
- Griefahn, D.; Wollnack, J.; Hintze, W.:
Principal component analysis for fast and automated thermographic inspection of internal structures in sandwich parts
in: Journal of Sensors and Sensor Systems, 3, pp. 105-111, 2014 doi:10.5194/jsss-3-105-2014
- Hintze, W.:
Neue Ansätze zur wirtschaftlichen Präzisionsbearbeitung von CFK-Strukturen
in: Bleicher, F.; Lammer, K. (Hrsg.): Industrie 4.0 – die intelligente Fabrik der Zukunft, Tagungsband, 2. Wiener Produktionstechnik Kongress 07.-08.05.2014, Klein Publishing, Wien, Österreich, 2014, S. 131-140, ISBN 978-3-903015-00-5
- Hintze, W.; Kothe, S.; Susemihl, H.:
Flexible Präzisionsbearbeitung von CFK-Großstrukturen mit Industrierobotern
in: Ingenieurspiegel 1/2014, Public Verlagsgesellschaft, Bingen, S. 24-26
- Eichenseer, C.; Hartig, C.; Schell, N.; Hintze, W.:
In situ determination of internal stresses in mixed ceramic cutting tools during friction testing using synchrotron ratiation
in: Journal of Production Engineering Research and Development, 2014 doi:10.1007/s11740-014-0535-1
- Schütte, C.:
Bohren und Hobeln von kohlenstofffaserverstärkten Kunststoffen unter besonderer Berücksichtigung der Schneide-Faser-Lage
Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 20, Hamburg, 2014, ISSN 1613-8244
- Hintze, W.; Clausen, R.; Schütte, C.:
The Cutting Force Vector in Drilling of Unidirectional CFRP - A New Approach for Process Analysis
Technical Report, CIRP Paris January Meetings, STC Cutting, Paris, 2014-01-23
2013
- Hintze, W.; Steinbach, S.:
Präzisionsbohren von CFK und Schichtverbunden
in: CFK-Valley Stade e.V. (Hrsg.): INNOVATION REPORT, 2-2013, S. 28-29.
INNOVATION REPORT, Ausgabe 2, 2-2013 (S. 28)
- Hintze, W.:
Optimierungspotenziale für die CFK-Bearbeitung
in: MM MaschinenMarkt CompositesWorld, (2013) 11, S. 12-15.
Online veröffentlicht unter
http://www.maschinenmarkt.vogel.de/compositesworld/articles/425074/
- Hintze, W.; Schütte, C.; Steinbach, S.:
Influence of the Fiber Cutting Angle on Work Piece Temperature in Drilling of Unidirectional CFRP
in: Denkena, B. (Hrsg.): Lecture Notes in Production Engineering: New Production Technologies in Aerospace Industry, Proceedings of the 4th Machining Innovations Conference, Hannover, September 2013, Springer, S. 137-143, doi:10.1007/978-3-319-01964-2_19
- Freising, M.; Kothe, S.; Rott, M.; Susemihl, H.; Hintze, W.:
Increasing Accuracy of Industrial Robots in Machining of Carbon Fibre Reinforced Plastics
in: Denkena, B. (Hrsg.): Lecture Notes in Production Engineering: New Production Technologies in Aerospace Industry, Proceedings of the 4th Machining Innovations Conference, Hannover, September 2013
Springer
ISBN 978-3-319-01963-5
- Hintze, W.; Wollnack, J.; Griefahn, D.:
Principal Component Analysis for Fast and Automated Thermographic Inspection of Internal Structures in Sandwich Parts
in: Schmitt, R.; Bosse, H. (Hrsg.): ISMTII 2013: Metrology - Master Global Challenges - "The 11th International Symposium on Measurement Technology and Intelligent Instruments", July 1st - July 5th, 2013, Aachen
Apprimus Verlag, RWTH, Aachen, Germany, 2013
ISBN 978-3-86359-138-0
- Hintze, W.; Hartmann, D.:
Modeling of delamination during milling of unidirectional CFRP
in: Procedia of the 14th CIRP Conference on Modeling of Machining Operations (CIRP CMMO 2013), Juni 13 - 14, 2013, Turin, Italien, Elsevier, Vol. 8, S. 443-448, doi:10.1016/j.procir.2013.06.131
- Hintze, W.; Hartung, F.; Kawala, D.; Klingelhöller, C.; Olesch, M.:
Efficient and Reliable Grinding of Landing Gear Parts
in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 4th International Workshop on Aircraft System Technologies (AST 2013), April 23 - 24, 2013, Hamburg, Germany
Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2013, S. 345-354, ISBN 978-3-8440-1850-9
- Hintze, W.; Möller, C.:
Hochleistungs-Schlichtfräsen dünnwandiger Titanbauteile
Unter Span - Das Magazin des Machining Innovations Network (2013) 1, S. 13
- Hintze, W.:
Präzisionsbearbeitung von CFK-Strukturen im Mobilitätssektor - Herausforderungen und Lösungen
In: Tagungsband zu "19. Nationales Symposium SAMPE Deutschland e. V. - Faserverbundwerkstoffe in der Energiewende", 27.-28. Februar 2013, Hamburg, S. 62-64, ISBN 978-3-941492-58-5
2012
- Eichenseer, C.; Wittmann, I.; Hartig, C.; Schell, N.; Hintze, W.:
In situ measurement of lattice strains in mixed ceramics under static thermal and mechanical loads (PDF),
HASYLAB Annual Reports 2012
- Hartmann, D.:
Delamination an Bauteilkanten beim Umrissfräsen kohlenstofffaserverstärkter Kunststoffe
Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 17, Hamburg, 2012
- Eichenseer, C.; Wittmann, I.; Hartig, C.; Schneider, G. A.; Schell, N.; Hintze, W.:
In situ measurement of lattice strains in mixed ceramic cutting tools under thermal and mechanical loads using synchrotron radiation
In: Production Engineering - Research and Development 7(2013)2-3, 01 Apr 2013, S. 283-289
available online 02 November 2012, doi:10.1007/s11740-012-0426-2
- Hintze, W.; Kothe, S.; Niermann, D.; Wollnack, J.; Borrmann, C.:
Reliable Machining of CFRP Components with Industrial Robots
ISCM 2012, 6th International Symposium on "Manufacturing Technology for Composite Aircraft Structures", 24.-25. October 2012, DLR Stade
- Hintze, W.; Hartmann, D.; Schütte, C.; Goßmann, U.:
Mechanisms and Avoidance of Delamination in Edge Milling of CFRP
Technical Report, CIRP General Assembly, STC Cutting, Hong Kong, 2012-08-24
- Hintze, W.; Hartmann, D.; Schubert, U.:
Stirnfräsen von CFK zur Fügeflächenherstellung und Reparaturvorbereitung
in: ZWF (2012) 6, Carl Hanser Verlag, München, S. 462-466 (http://www.zwf-online.de/ZW110775)
- Hintze, W.; Kober, H.; Kothe, S.-M.; Ograbisz, P.; Schütte, C.:
Temperaturen beim Fräsen von Composites beherrschen - Mit neuen Analysemethoden zu optimalen Prozessen
Unter Span - Das Magazin des Machining Innovations Network (2012) 1, S. 10-11 (PDF)
- Hintze, W.; Hartmann, D.; Goßmann, U.:
Kantenqualiät beim Umrissfräsen von CFK verbessern - Modellgestützte Delaminationsanalyse erlaubt angepasste Bearbeitungsstrategien
in: VDI-Z 154(2012) 1/2, Springer-VDI-Verlag, Düsseldorf, 2012, S. 24-27
2011
- Hintze, W.; Kothe, S.-M.; Kober, H.:
Investigations on process temperature in machining of CFRP composites
in: Proceedings of the 6th International Conference "Supply on the wings", AIRTEC 2011, 02.-04.11.2011, Frankfurt (Main), 2011
- Hintze, W.; Hartmann, D.; Schütte, C.:
Occurrence and propagation of delamination during the machining of carbon fibre reinforced plastics (CFRPs) - An experimental study
in: Composites Science and Technology 71(2011)15, 24 Oct 2011, S. 1719-1726
available online 22 August 2011, doi:10.1016/j.compscitech.2011.08.002
- Hintze, W.; Möller, C.:
Innovation in der Zerspanungstechnologie von Leichtbauwerkstoffen
Unter Span - Das Magazin des Machining Innovations Network (2011) 1, S. 19
- Frömming, H.:
Zerspanung von WC-Co-Hartmetall im unterbrochenen Schnitt
Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 13, Hamburg, 2011
- Schütte, C.:
Prozesssichere Zerspanung aktueller CFK-Werkstoffe
in: Tagungsband des OTTI-Fachforum "Neue Werkstoffe wirtschaftlich zerspanen- Werkzeuge, Fertigungsprozesse, Problemlösungen, Perspektiven", 06.-07. Juni 2011, OTTI e. V., Regensburg, 2011, S. 195-215
- Schütte, C.; Dose, F.:
Wirtschaftliche und prozesssichere Bohrbearbeitung von CFK
in: lightweightdesign 2/2011, Verlag Vieweg+Teubner, Wiesbaden, 2011, S. 50-57, ISSN 1865-4819
- Eichenseer, C.; Wittmann, I.; Schneider, G. A.; Hartig, C.; Hintze, W.:
Stress-strain evaluation of mixed ceramics under thermal and mechanical loads using x-ray diffraction (PDF),
HASYLAB Annual Reports 2011
- Hintze, W.; Wollnack, J.; Backhaus, S.; Kothe, S.-M.; Neuendorf, M.:
Process Monitoring for Reliable Machining of CFRP Structures
in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 3rd International Workshop on Aircraft System Technologies (AST 2011), March 31 - April 01, 2011, Hamburg, Germany
Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2011, S. 413-424, ISBN 978-3-8322-9904-0
2010
- Eichenseer, C.; Hintze, W.; Schneider, G. A.; Röhlsberger, R.; Glaser, L.; Schell, N.:
X-ray characterization of a TiAlN-coating on a mixed ceramic substrate with a resolution of a few microns (PDF),
HASYLAB Annual Reports 2010
- Hintze, W.; Dose, F.; Hartmann, D.; Schütte, C.:
Assessment of surface integrity of machined CFRP - Methods and Results
in: Proceedings of the 5rd International Conference "Supply on the wings", AIRTEC 2010, 02.-04.11.2010, Frankfurt (Main), 2010, ISBN 978-3-942939-00-3
- Schütte, C.:
Prozesssichere Zerspanung aktueller CFK-Werkstoffe
in: Tagungsband des OTTI-Fachforum "Neue Werkstoffe wirtschaftlich zerspanen- Werkzeuge, Fertigungsprozesse, Problemlösungen, Perspektiven", 09.-10. Juni 2010, OTTI e. V., Regensburg, 2010, S. 259-275
- Niermann, D.; Hintze, W.; Wollnack, J.:
The Process Chain of CFRP XXL-Structures in CFK Nord
in: Proceedings of the 4th International CFK-Valley Stade Convention 2010, June 15-16, 2010, Stade, Germany, S. 16-19
- Kindler, J.:
Werkstückqualität und Standzeitoptimierung von Zerspanwerkzeugen bei der Umrissbearbeitung von kohlenstofffaserverstärkten Kunststoffen
Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 12, Hamburg, 2010
- Hintze, W.; Möller, C.:
Diamanten machen's möglich - Polierschleifprozess erzeugt automatisiert spiegelnde Oberflächen
Form + Werkzeug, Hanser Verlag (2010), Online veröffentlicht
- Sellmer, D.:
Untersuchungen zur Verbesserung des Arbeitsergebnisses beim Vollbohren unter besonderer Berücksichtigung der Prozesskräfte und der Spanbildung
Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 10, Hamburg, 2010
2009
- Hintze, W.; Frömming, H.; Dethlefs, A.:
Influence of machining with defined cutting edge on the subsurface microstructure of WC-Co parts
in: International Journal of Refractory Metals and Hard Materials 28(2010)2 S.274-279, available online 3 November 2009, DOI:10.1016/j.ijrmhm.2009.10.012
- Hintze, W.; Frömming, H.:
Upgrading the Toolbox of Machining Cemented Tungsten Carbides
in: Sigl, L.S.; Rödhammer, P.; Wildner, H. (eds.): Proceedings of the 17th Plansee Seminar, International Conference on High Performance PM Materials, May 25 - 29, 2009, Reutte/Austria
- Gotsch, F.:
Untersuchungen zum Zerspanverhalten von Elastomerschäumen mit dem Ziel einer wirtschaftlichen Fertigung von Feder-Dämpfer-Bauteilen
Dissertation, erschienen in: Nedeß, Chr.; Hintze, W. (Hrsg.): Wissen schafft Innovation, Nr. 8, Hamburg, 2009
- Hintze, W.; Friedewald, A.; Dose, F.:
Innovative Process Planning and Diagnosis by Integrated Knowledge Management
in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 2nd International Workshop on Aircraft System Technologies (AST 2009), March 26-27, 2009, Hamburg, Germany
Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2009, S. 199-210, ISBN 978-3-8322-8071-0
- Möller, C.:
Untersuchungen zum Drehen von gesinterten WC-Co-Hartmetallwalzringen
Dissertation, erschienen in: Nedeß, Chr.; Hintze, W. (Hrsg.): Wissen schafft Innovation, Nr. 7, Hamburg, 2009
2008
- Hintze, W.; Hartmann, D.; Schütte, C.; Schwerdt, M.:
Wet machining of CFRP
in: Proceedings of the 3rd International Conference "Supply on the wings", AIRTEC 2008, 11.-13.11.2008, Frankfurt (Main), available on CD only
- Hintze, W.; Möller, C.:
Automatisierte Erzeugung spiegelnder Oberflächen durch 3D-Schleifen
Sachbericht KF0202201PK5, Pro Inno II, 2008
- Bhattacharya, A. K.; Zimmermann, K.; Schneider, G. A.; Hintze, W.:
Influence of Surface Modification on the Cutting Performance of Reaction-Sintered Al2O3-TiOC Ceramics
in: Journal of the American Ceramic Society 91(2008)9, S. 2982-2986
DOI:10.1111/j.1551-2916.2008.02559.x
2007
- Hintze, W.; Dose, F.; Hartmann, D.; Santos Quiroz, S.; Schwerdt, M.:
Cutting, abrasive and laser technologies for CFRP machining: state of the art and future trends
in: Proceedings of the 2nd International Conference "Supply on the wings", AIRTEC 2007, 24.-25.10.2007, Frankfurt (Main), available on CD only
- Püschel, A.:
Randzonenmodifikation aluminothermisch hergestellter Mischkeramiken zur Hartbearbeitung
Dissertation, erschienen in: Berichte aus der Materialwissenschaft, Shaker, Aachen, 2007
- Zimmermann, K.; Schneider, G. A.; Bhattacharya, A. K.; Hintze, W.:
Surface Modification of Al2O3/TiC Cutting Ceramics
in: Journal of the American Ceramic Society 90(2007)12, S. 3773-3778
DOI:10.1111/j.1551-2916.2007.02039.x
- Hintze, W.; Hartmann, D.; Schwerdt, M.:
Machining of CFRP
in: Proceedings of the 1st International CFK-Valley Stade Convention 2007, June 13-14, 2007, Stade, Germany, S. 53-57
- Hintze, W.; Clausen, R.; Hartmann, D.; Kindler, J.; Santos, S.; Schwerdt, M.; Stöver, E.:
Precision of machined CFRP
The challenge of dimensional accuracy
in: Proceedings of the 1st International Workshop on Aircraft System Technologies (AST 2007), March 29-30, 2007, Hamburg, Germany
Shaker Verlag Aachen, 2007, S. 361-374
- Hintze, W.; Frömming, H.:
Schlichtfräsen eröffnet neue Einsatzbereiche
Grundlagenuntersuchungen zum Fräsen von gesintertem Hartmetall
WB Werkstatt + Betrieb 03/2007, S. 63-67
2006
- Hintze, W.; Hartmann, D.; Kindler, J.; Stöver, E.:
High Productivity Cutting of CFRP Composite Structures: Workpiece Quality and Tool Wear
in: Proceedings of the 1st International Conference "Supply on the wings", AIRTEC 2006, 18.-19.10.2006, Frankfurt (Main), available on CD only
- Hintze, W.; Eglins, F.:
Automatisierte Erzeugung spiegelnder Oberflächen durch 3D-Schleifen
Zwischenbericht KF0202201PK5, Pro Inno II, 2006
- Swiostek, J.; Bober, J.; Blawert, C.; Letzig, D.; Hintze, W.; Kainer, K. U.:
Die forging of commercial and modified magnesium alloys
7th International Conference on Magnesium Alloys and their Applications, Dresden, 06.-09.11.2006
- Hintze, W.; Clausen, R.; Santos Quiroz, S.; Schwerdt, M.:
Wirtschaftliche Zerspanung von Leichtbaustrukturen durch den Einsatz innovativer Hartmetallschneidstoffe und Diamantbeschichtungen
Congress Intelligente Leichtbau Systeme (ILS) 2006, Hannover, 05./06.09.2006
- Hintze, W.; Frömming, H.; Gotsch, F.:
Spanende Bearbeitung von Elastomerschäumen
Analyse der reversiblen Verformungen und der Zerspankraft beim Drehen kompressibler PUR-Schäume
wt Werkstattstechnik online 96(2006)9, S. 662-668
- Hintze, W.; Möller, C.:
Randzonenuntersuchung an gedrehten Hartmetallbauteilen
in: Industrie Diamanten Rundschau 40(2006)II, S. 48-55
2005
- Hintze, W.; Eglins, F.:
Entwicklung eines neuen Verfahrens zur maschinellen Erzeugung von Oberflächen mit höchster Güte
Abschlussbericht Investitions- und Förderbank Niedersachsen, 2005
- Joswig, D.:
Untersuchung zum Zerspanverhalten weicher Elastomerwerkstoffe
Dissertation, erschienen in: Nedeß, Chr.; Hintze, W. (Hrsg.): Wissen schafft Innovation, Nr. 3, Hamburg, 2005
- Clausen, R.; Hintze, W.; Stöver, E.:
Glare - ein neuer Werkstoff im Flugzeugbau
Grundlagen der Bohrbearbeitung
in: Zeitschrift für wirtschaftlichen Fabrikbetrieb 100(2005)3, S. 111-116
2004
- Hintze, W.; Joswig, D.; Gotsch, F.:
Spanende Fertigung von Elastomerdichtungen
in: Berger, K.-F.; Kiefer, S. (Hrsg.): Jahrbuch Dichtungstechnik 2005, Hüthig, Heidelberg, 2004, S. 321-326, ISBN 3-7785-2942-0 - Hintze, W.; Gotsch, F.; Möller, C.; Püschel, A.; Santos Quiroz, S.; Stöver, E.:
Manche mögen's nicht so heiß - Thermische Wechselwirkungen beim Trockenbohren von Leichtbaustrukturen
in: Maschinenmarkt 110(2004)37, S. 78-83 - Hintze, W.; Möller, C.:
Drehtechnologie für Hartmetallwalzen
74. Tagung der Arbeitsgemeinschaft Internationaler Kalibreure u. Walzwerksingenieure (AIKW), Straßburg, September 2004 - Hintze, W.; Joswig, D.; Gotsch, F.:
Mechanische Grundlagen der Zerspanung von Elastomerdichtungen
Tagungsband zu "V. Hamburger Dichtungstechnisches Kolloquium - Dynamische Dichtungen", Radialwellendichtringe, TUHH, Hamburg, 03./04.06.2004
2003
- Hintze, W.; Schneider, G. A.; Püschel, A.:
Mikromechanische Bewertung aluminothermisch hergestellter Schneidstoffe
Arbeitsbericht 2003 zum Teilprojekt D4 des Sonderforschungsbereiches 371, TUHH, 2003
- Hintze, W.:
Forschen an den Grenzen der Zerspanbarkeit
TUHH-Spektrum (2003) 2
- Hintze, W.; Schneider, G. A.; Püschel, A.:
Reaktionsgesinterte Mischkeramiken zur Hartbearbeitung
in: VDI-Z Spezial Werkzeuge II (2003), S. 26-30
- Hintze, W.; Nedeß, Chr.; Möller, C.:
Auf die harte Tour
CVD-Dickschichtdiamant verringert den Verschleiß und die Zerspankräfte in der Hartmetallbearbeitung
in: Maschinenmarkt 109(2003)25, S. 26-30
- Hintze, W.; Clausen, R.; Stöver, E.; Plucinski, M.:
Bohren für den A380
Werkzeug- und Prozessentwicklung im Team
in: TUHH SPEKTRUM - Special Luftfahrtforschung, II/2003, S. 26-27
- Hintze, W.; Santos Quiroz, S.; Kerse, N.:
Concurrent Engineering beim Airbus A380
Planung manueller Montagearbeitsplätze mit Virtual Reality
in: TUHH SPEKTRUM - Special Luftfahrtforschung, II/2003, S. 28-29
2002
- Nedeß, Chr.; Claussen, N.; Hintze, W.; Janssen, R.; Püschel, A.; Durlu, N.:
Mikromechanische Bewertung aluminothermisch hergestellter Schneidstoffe
in: Arbeitsbericht 2000-2002 des Sonderforschungsbereiches 371, TUHH, 2002, S. 373-394
- Hintze, W.; Möller, C.:
Heutige Tendenzen der Ultrahartbearbeitung
Ein Bericht der TUHH über das Drehen gesinterter Hartmetallwalzen
in: Mensch & Technik III/2002, VDI Hamburger Bezirksverband e.V., S. 14-16
- Nedeß, Chr.; Hintze, W.; Halver, M.; Möller, C.:
Hartdrehen statt Schleifen
HSS-Schneidplatten flexibel, wirtschaftlich und funktionsgerecht hart bearbeiten.
in: Maschinenmarkt 108(2002)25, S. 38-43
- Hintze, W.; Nedeß, Chr.; Joswig, D.:
Analyse und Reduktion dynamischer Verformungen beim Drehen von Elastomeren
Tagungsband zu "IV. Hamburger Dichtungstechnisches Kolloquium - Dynamische Dichtungen", Radialwellendichtringe, Teil 2, TUHH, Hamburg, 23./24.05.2002
- Hintze, W.; Isecke, S.; Joswig, D.:
Spritzgießen ade - Fräsen von Elastomerbauteilen in kleinen Stückzahlen ist schnell und flexibel
in: Maschinenmarkt 108(2002)11, S. 36-39
2000
- Bargel, Frank:
Untersuchung der Zerspanbarkeit eines Acrylnitril-Butadien-Elastomers mit dem Ziel der Herstellung von rotationssymmetrischen Dichtungen durch Drehen
Dissertation, erschienen in: Fortschritt-Berichte VDI, Reihe 2, Nr. 565, VDI-Verlag, Düsseldorf, 2000
- Mohammed, A.; Hagel, H.; Michels, K. P.; Burkhart, G.; Wimmer, K.; Janta, R.; Nedeß, Chr.; Hintze, W.; Rohwer, A.:
Optimization of material, geometrical and tribological characteristics for electrode-nipple-joints used in EAF´s
Tagungsband EUROCARBON 2000, Berlin, 09.-13.07.2000
- Hintze, W.; Nedeß, Chr.; Bargel, F.; Joswig, D.:
Technologie der spanenden Bearbeitung von Elastomerdichtungen
Tagungsband zu "III. Hamburger Dichtungstechnisches Kolloquium - Dynamische Dichtungen", Radialwellendichtringe, TUHH, Hamburg, 15./16.06.2000
1999
- Scherbarth, S.:
Der Einfluß der Schneidkeilgeometrie auf das Zerspanverhalten beim Fräsen von Stahlwerkstoffen mit beschichtetem Hartmetall
Dissertation, erschienen in: Berichte aus der Fertigungstechnik, Shaker, Aachen, 1999
1998
- Gatermann, H.:
Reibungseinflüsse auf die Spanbildung beim Drehen
Dissertation, erschienen in: Fortschritt-Berichte VDI, Reihe 2, Nr. 497, VDI-Verlag, Düsseldorf, 1998
- Nedeß, Chr.; Bargel, F.:
Zerspanung entropieelastischer Werkstoffe mit geometrisch bestimmter Schneide
in: VDI-Zeitung 140(1998)1/2, S. 28-31
1997
- Fang, N.; Wang, M.; Nedeß, Chr.:
Development of the new-type indexable with helical rake faces
in: Proceedings of the Institution of Mechanical Engineers, Journal of Engineering Manufacture, 1997, Vol 211 Part B, pp. 159-164
- Nedeß, Chr.; Gatermann, H.:
Einflüsse der Beschichtung auf das Spanbruchverhalten. Hartmetall-Wendeschneidplatten beim Drehen langspanender Werkstoffe
in: VDI-Zeitung Special Werkzeuge August '97, S. 40-45
- Nedeß, Chr.; Beck, M.:
Überwachen des Gewindebohrens
Nutzbar machen, was der Mensch hört(e) - Schallanalyse als Grundlage.
in: VDI-Zeitung Special Werkzeuge April '97, S. 40-46
1996
- Nedeß, Chr.; Pflueg, Chr.:
Real-Time Monitoring and Controlling of Chip Form in Turning Processes with Acoustic Emission Using Thin Film Sensors
24th North American Manufacturing Research Conference (NAMRC XXIV), University of Michigan, Ann Arbor/Michigan, USA, 21.-23.05.1996
1994
- Günther, U.:
Analyse und Optimierung des Einsatzverhaltens von Bohrwerkzeugen mit Hartmetall-Wendeschneidplatten
Dissertation, TUHH, 1994
- Nedeß, Chr.; Pflueg, Chr.:
Chip Form Monitoring in Turning Internal Surfaces with Acoustic Emission using Thin Film Sensors
7th International Conference on Production/Precision Engineering (7th ICPE), Nippon Convention Center (MAKUHARI MESSE), Chiba, Japan, 1994
1992
- Schwedler, M.:
Dünnschichtsensoren für die Überwachung von Maschinenbauteilen
Dissertation, TUHH, 1992
- Nedeß, Chr.; Günther, U.:
Radial Forces in Short Hole Drilling and their Effects on Drill Performance
20th North American Manufacturing Research Conference (NAMRC XX), Washington State University, Pullman, Washington USA, 20.-22.05.1992
- Nedeß, Chr.; Günther, U.:
Bohren mit Hartmetall-Wendeplatten-Werkzeugen. Untersuchung der Radialkräfte und ihrer Auswirkungen auf das statische und dynamische Verhalten
in: VDI-Zeitung 134(1992)2, S. 49-58
- Weindorf, T.:
Schwingungen beim Schaftfräsen
Modellgestützte Analyse des Schwingungsverhaltens, Ratterursachen, Abhilfemaßnahmen.
Dissertation, erschienen in: Fortschritt-Berichte VDI, Reihe 2, Nr. 235, VDI-Verlag, Düsseldorf, 1992
1991
- Nedeß, Chr.; Schwedler, M.:
Diagnosis of Faults with Thin-film Sensors in a Multiple-Spindle-Drilling-Head
19th North American Manufacturing Research Conference (NAMRC XIX),
The University of Missouri-Rolla, Rolla, Missouri USA, 22.-24.05.1991
1990
- Nedeß, Chr.; Weindorf, T.:
Zur dynamischen Steifigkeit von Werkzeugen und ihrer Aufnahme
in: VDI-Zeitung 132(1990)9, S. 110-119
- Hintze, W.:
Modellgestützte Spanbruchbeurteilung beim Drehen
Dissertation, TUHH, 1990
- Nedeß, Chr.; Himburg, T.; Holst, G.:
Verschleißerfassung bei Schneidplatten mit komplexer Geometrie
in: VDI-Zeitung 130(1990)1, S. 51-56
1989
- Himburg, T.; Keller, H.:
Universelles Rechnerkonzept für die Entwicklung von Überwachungssystemen
in: VDI-Zeitung 129(1989)2, S. 71-75
- Nedeß, Chr.; Schwedler, M.:
Flach und klein - aber fein. Überwachung und Fehlerfrühdiagnose an Maschinenbauteilen mit Sensoren der Dünnschichttechnik
in: Maschinenmarkt 95(1989)39, S. 72-79
- Nedeß, Chr.; Hintze, W.:
Characteristic Parameters of Chip Control in Turning Operations with Indexable Inserts and Three-Dimensionally Shaped Chip Formers
Annals of the CIRP Vol. 38/1/1989, CIRP-Konferenz " Manufacturing Technology", Trondheim, Norway, 21.-26.08.1989
1988
- Himburg, T.:
Die Dynamik des Bohrvorganges als Grundlage eines Überwachungskonzeptes
Dissertation, TUHH, 1988
- Nedeß, Chr.; Himburg, T.:
Drilling Dynamics
A Fundamental Base for Drill-Life-Monitoring.
16th North American Manufacturing Research Conference (NAMRC XVI), University of Illinois, Urbana-Champaign, USA, 25.-27.05.1988
1987
- Nedeß, Chr.; Hintze, W.; Khanji, M.:
Die Hartmetallschneidplatte als Teilkomponente des Werkzeuges in der CIM-Linie
in: tz für Metallbearbeitung 81(1987)5, S. 30-35
- Nedeß, Chr.; Schwedler, M.:
Dünnschichtsensoren zur Diagnose von Maschinenschäden
in: VDI-Zeitung 129(1987)9, S. 54-56
- Nedeß, Chr.; Hintze, W.:
Wirkungsweise eingesinterter Spanformstufen
Technologische Grundlagen für die Schneidplattenauswahl und -konstruktion
in: VDI-Zeitung 129(1987)10, S. 106-112
1986
- Nedeß, Chr.; Himburg, T.:
Automatisierte Überwachung des Bohrens
Dynamischer Bearbeitungsprozeß als Signalquelle
in: VDI-Zeitung 128(1986)17, S. 651-657
- Nedeß, Chr.; Himburg, T.; Schwedler, M.:
Stabilitätsverhalten von Innendrehwerkzeugen
in: VDI-Zeitung 128(1986)11, S. 409-414
- Nedeß, Chr.:
Werkzeuge in der CIM-Linie
in. CIM-Praxis 09/1986, S. 62-66
- Nedeß, Chr.; Hintze, W.:
Untersuchung der Spanform beim Drehen mit Hilfe der Fotografie
in: Yashica/Contax News Nr. 13, 4/86
1984
- Nedeß, Chr.:
Schnittwertoptimierung bei teilausgelasteten Fertigungssystemen
in: tz für Metallbearbeitung 78(1984)12, S. 49-51