Veröffentlichungen der Arbeitsgruppe Produktionstechnik
2023
Koch, P.; Rawal, P.; Töpfer, N.; Haß, T.; Böhlmann, C.; Hintze, W.: Modular lightweight robot system for aircraft production using a generic OPC UA skill concept in: Production Engineering 17 (2023), p. 329-339, Springer Berlin Heidelberg. available online 15 March 2023 DOI: 10.1007/s11740-023-01183-w
2022
Rana, P.; Hintze, W.; Schall, T.; Polley, W.: Implementation of MC-SPG particle method in the simulation of orthogonal turning process in: M. Liewald, A. Verl, T. Bauernhansl, H.-C. Möhring: Production at the Leading Edge of Technology, Proceedings of the 12th Congress of the German Academic Association for Production Technology (WGP), University of Stuttgart, October 2022, Springer Verlag Berlin, 2022, DOI: 10.1007/978-3-031-18318-8_37
Hintze, W.; Brouschkin, A.; Köttner, L.; Bluehm, M.: Model Based Prediction of Force and Roughness Extrema Inherent in Machining of Fibre Reinforced Plastics Using Data Merging in: M. Liewald, A. Verl, T. Bauernhansl, H.-C. Möhring: Production at the Leading Edge of Technology, Proceedings of the 12th Congress of the German Academic Association for Production Technology (WGP), University of Stuttgart, October 2022, Springer Verlag Berlin, 2022, DOI: 10.1007/978-3-031-18318-8_5
Romanenko, D.; Jothi Prakash, V.; Kuhn, T.; Moeller, C.; Hintze, W.; Emmelmann, C.: Effect of DED process parameters on distortion and residual stress state of additively manufactured Ti-6Al-4V components during machining in: Proceedings of the 12th CIRP Conference on Photonic Technologies (LANE 2022), Fuerth, Germany, Procedia CIRP 111 (2022) 271-276, DOI: 10.1016/j.procir.2022.08.020
Hintze W.; Möller C.; Ploog P.; Bobzin K.; Kalscheuer C.; Carlet M.; Stachowski N. Influence of self-lubricating tool coatings on cutting temperature and coefficient of friction during turning of Ti6Al4V
in: Proceedings of the 20th Plansee Seminar, International Conference on Refractory Metals and Hard Materials, May 30 – June 3, 2022, Reutte/Austria
Hintze W.; Hinrichs M; Rosenthal O.; Schleinkofer U.; Venturini R.; Tuned mass dampers for boring bars with small diameter
in: Proceedings of the 20th Plansee Seminar, International Conference on Refractory Metals and Hard Materials, May 30 – June 3, 2022, Reutte/Austria
Hintze, W.; Romanenko, D.; Molkentin, L.; Koettner, L.; Mehnen, J.: Holistic process monitoring with machine learning classification methods using internal machine sensors for semi-automatic drilling in: Proceedings of the 55th CIRP Conference on Manufacturing Systems (CMS 2022), Lugano, Switzerland, Procedia CIRP 107 (2022) 972-977, DOI: 10.1016/j.procir.2022.08.020
Brillinger, C.; Kallipalayam Murugesan, S.K.; Moeller, C.; Boehlmann, C.; Hintze, W.; Niermann, D.: Accuracy Analysis for a Flow Line Process using a Mobile Holding Fixture for Machining CFRP Components SAE Technical Paper 2022-01-0041, ISSN 0148-7191 available online 08. März 2022, DOI: 10.4271/2022-01-0041
Breitzke, A.; Hintze, W.: Workshop-suited geometric errors identification of three-axis machine tools using on-machine measurement for long term precision assurance in: Precision Engineering (2022), ISSN 0141-6369 available online 20. Februar 2022, DOI: 10.1016/j.precisioneng.2022.02.006
Lissek, F.; Kaufeld, M.; Bergmann, J.P.; Hintze, W.: Eine Frage des Timings – Schädigungsfreies Bohren nachgiebiger CFK-Strukturen in: Werkstatt+Betrieb, 17.02.2022. Online veröffentlicht unter https://www.werkstatt-betrieb.de/a/article-358589
Hintze, W.; Köttner, L.; Brouschkin, A.; Blühm, M.; Jakele, L.: A General Unique Description of Cutting Direction and Engagement for Arbitrary Oblique Cutting of Orthotropic Materials – Modeling and Validation for Grinding of Unidirectional CFRP Technical Report, CIRP Winter Meetings, STC C - Cutting, Paris, 2022-02-17
2021
Bobzin, K.; Brögelmann, T.; Carlet, M.; Stachowski, N.; Hintze, W.; Möller, C.; Ploog, P.: Self-lubricating CrAlVN coatings for turning of Ti6Al4V: oxidation and wear behavior Material Science & Engineering Technology (Wiley) Dezember 2021, Volume 52, Issue 12, S. 1394-1412, DOI: 10.1002/mawe.202100042
Hintze, W.; Köttner, L.: Curved Circular Cutting of lightweight Structures China-Germany-Japan Workshop on Advanced Manufacturing of New Energy Vehicles, 08.–10. Dezember 2021, Composites United e.V.,Virtual Workshop
Bobzin, K.; Kalscheuer, C.; Carlet, M.; Stachowski, N.; Hintze, W.; Möller, C.; Ploog, P.: Wear development of self-lubricating CrAlVN coatings during turning Ti6Al4V in: Denkena, B. (Hrsg.): Procedia Manufacturing of the 21st Machining Innovations Conference for Aerospace Industry 2021 (MIC 2021), Hannover, Volume 21 (2021) S. 70-77, SSRN available online 17. November 2021, DOI: 10.2139/ssrn.3947799
Hintze, W.; Möller, C.; Romanenko, D.; Junghans, S.: Adaptive Präzisionsbearbeitung additiv gefertigter Leichtbaustrukturen in der digitalisierten Prozesskette in: Unter Span - Magazin des Manufacturing Innovations Network (2021), S. 42-43, ISSN 2365-7006
Mehnen, J.; Hintze, W.; Köppe, M.: Influence of contour radius and fiber orientation on heat accumulation during machining of unidirectional CFRP in: MM Science Journal 2021-11-01, Proceeding of 16th International Conference on High Speed Machining (HSM 2021), 26–27 Oktober 2021, Darmstadt, ISSN 1803-1269, S. 5085-5092, DOI: 10.17973/MMSJ.2021_11_2021156
Rana, P.; Hintze, W.; Schall, T.; Polley, W.: Study on the Influence of the Coating Thickness in Turning of a Hard to Machine Material Using FEM-Simulation in: Behrens, B.-A.; Brosius, A.; Drossel, W.-G.; Hintze, W.; Ihlenfeldt, S.; Nyhuis, P. (Eds.): Production at the leading edge of technology, Proceedings of the 11th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 29 - September 30, Springer-Verlag, Berlin, 2021, S. 256-264, ISBN 978-3-030-78424-9, DOI: 10.1007/978-3-030-78424-9_29
Schulze, B.; Rawal, P.; Kothe, S.; Hintze, W.: Subsequent Synchronization of Individual Monitoring Systems for Machining of Aircraft Structures via a Data Collector Using OPC UA in: Behrens, B.-A.; Brosius, A.; Drossel, W.-G.; Hintze, W.; Ihlenfeldt, S.; Nyhuis, P. (Eds.): Production at the leading edge of technology, Proceedings of the 11th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 29 - September 30, Springer-Verlag, Berlin, 2021, S. 292-300, ISBN 978-3-030-78424-9, DOI: 10.1007/978-3-030-78424-9_33
Möller, C.; Hintze, W.; von Wenserski, R.: Impact Separation of Support Structures from Laser Powder Bed Fusion Generated LPBF Parts in: Behrens, B.-A.; Brosius, A.; Drossel, W.-G.; Hintze, W.; Ihlenfeldt, S.; Nyhuis, P. (Eds.): Production at the leading edge of technology, Proceedings of the 11th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 29 - September 30, Springer-Verlag, Berlin, 2021, S. 384-391, ISBN 978-3-030-78424-9, DOI: 10.1007/978-3-030-78424-9_43
Behrens, B.-A.; Brosius, A.; Drossel, W.-G.; Hintze, W.; Ihlenfeldt, S.; Nyhuis, P (Eds.): Production at the leading edge of technology Proceedings of the 11th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 28 - September 29, Springer-Verlag, Berlin, 2021, ISBN 978-3-030-78423-2, ISBN 978-3-030-78424-9 (eBook)
Hintze, W.: CFK-Bearbeitung. Trenntechnologien für Faserverbundkunststoffe und den hybriden Leichtbau Springer Vieweg, Berlin. ISBN 978-3-662-63264-2, ISBN 978-3-662-63265-9 (eBook), DOI: 10.1007/978-3-662-63265-9
von Wenserski, R.: Helixfräsen und Bohren von laseradditiv gefertigten Bauteilen aus Titan für Luftfahrtanwendungen Dissertation, erschienen in: Lödding, H.; Hintze, W.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 47, Hamburg 2021, ISSN 1613-8244, DOI: 10.15480/882.3723
Mehnen, J.; Hintze, W.: Prozessüberwachung durch Machine Learning beim semi-automatischen Nietbohren in der Luftfahrtindustrie METAV-Digital 2021 Websession im Bereich "Intelligente Produktion", Vortrag, 08. April 2021, Zur Aufzeichnung
Möller, C.; Dege, J. H.; Heuwinkel, M.: Entwicklung eines tangentialen Walzenstirnfräskonzeptes für Titanstrukturbauteile Hanser Tagungen "Schwer zerspanbare Werkstoffe in der industriellen Praxis", Vortrag, Digitales Event, 02.-03. März 2021
Hintze, W.; Rosenthal, O.; Hinrichs, M.; Steinbach, S.: Zerspanung von gesintertem Hartmetall - Grundlagen und Anwendung Hanser Tagungen "Schwer zerspanbare Werkstoffe in der industriellen Praxis", Vortrag, Digitales Event, 02.-03. März 2021
2020
Hintze, W.; Ploog, P.; Bluehm, M.; Möller, C.: Development of a process-oriented tribological test rig for the performance assessment of tool coatings in turning of titanium Ti6Al4V in: Denkena, B. (Hrsg.): Procedia Manufacturing of the 20th Machining Innovations Conference for Aerospace Industry - MIC 2020, Hannover, Volume 20 (2020) S. 107-115, SSRN available online 03 November 2020 doi.org/10.2139/ssrn.3724119
Hintze, W.; Rosenthal, O.; Möller, C.: Was die Stabilität von Werkzeugspannmitteln beeinflusst in: VDW-Branchenreport September 2020
Kothe, S.; Diehl, B.; Niermann, D.; Chen, M.; Wolf, M.; Hintze, W.: Automated Assembly of Thermoplastic Fuselage Structures for Future Aircrafts in: Behrens, B.-A.; Brosius, A.; Hintze, W.; Ihlenfeldt, S.; Wulfsberg, J. P. (Eds.): Production at the leading edge of technology, Proceedings of the 10th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 23 - September 24, Springer-Verlag, Berlin, 2020, S. 467-475, ISBN 978-3-662-62137-0, DOI: 10.1007/978-3-662-62138-7_47
Köttner, L.; Mehnen, J.; Romanenko, D.; Bender, S.; Hintze, W.: Process monitoring using machine learning for semi-automatic drilling of rivet holes in the aerospace industry in: Behrens, B.-A.; Brosius, A.; Hintze, W.; Ihlenfeldt, S.; Wulfsberg, J. P. (Eds.): Production at the leading edge of technology, Proceedings of the 10th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 23 - September 24, Springer-Verlag, Berlin, 2020, S. 497-507, ISBN 978-3-662-62137-0, DOI: 10.1007/978-3-662-62138-7_50
Behrens, B.-A.; Brosius, A.; Hintze, W.; Ihlenfeldt, S.; Wulfsberg, J. P. (Eds.): Production at the leading edge of technology Proceedings of the 10th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 23 - September 24, Springer-Verlag, Berlin, 2020, ISBN 978-3-662-62137-0
Hintze, W.; Mehnen, J.; Schmid, M.; Süess, B.; Weigand, M.: Alle Parameter genau abgestimmt – Hochleistungs-CFK-Bearbeitung mit diamantbeschichteten Bohr- und Fräswerkzeugen in: Diamond Business, 03. September 2020
Brieskorn, L.; Hintze, W.: Automated removal of carbon fiber reinforced plastic layers for the repair by adhesive bonding in: Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering, 234(13) 2011–2022 available online 5 August 2020 doi.org/10.1177/954410020947913
Hintze, W.; von Wenserski, R.; Junghans, S.; Möller, C.: Finish machining of Ti6Al4V SLM components under consideration of thin walls and support structure removal in: Procedia Manufacturing, Volume 48, 2020, p. 485-491. available online 23 June 2020 doi.org/10.1016/j.promfg.2020.05.072
Möller, Chr.: Entwicklung eines hochgenauen Bearbeitungsroboters durch den Einsatz zusätzlicher Messtechnik Dissertation, erschienen in: Hintze, W.; Mayer, B.; Wollnack, J.; Niermann, D. (Hrsg.): Forschung für die Produktionstechnik von Morgen, Band 4, Fraunhofer IFAM, Stade, Fraunhofer Verlag, Stuttgart, 2020, ISBN 978-3-8396-1600-0
Hintze, W.; Rosenthal, O.; Möller, C.: Tool holder influence in roughing with end mills Technical Report, CIRP Winter Meetings, STC-M Machines, Paris, 2020-02-21
Rosenthal, O.; Hintze, W.; Möller, C.: Assessment of tool holder performance in roughing with end mills Process dynamics and surface formation In: Production Engineering 14 (2020), p. 253–263, Springer Berlin Heidelberg. available online 08 January 2020 doi.org/10.1007/s11740-019-00944-w
2019
Rawal, P.; Brillinger, C.; Böhlmann, C.; Hintze, W.: Sensor based online quality monitoring system for detection of milling defects on CFRP structures in: CEAS Aeronautical Journal (2019) available online 21 December 2019 doi.org/10.1007/s13272-019-00436-8 Springer Link s13272-019-00436-8
Maiß, O.; Bluehm, M.; Ploog, P.; Hintze, W.: Straightening of thin-walled titanium components by defined deep rolling LightMAT - 3rd Conference & Exhibition on Light Materials – Science and Technology, Manchester, UK, 04.11.2019
Mehnen, J.; Hintze, W.; Köttner, L.; von Wenserski, R.: Temperature field due to a moving heat source in machining orthotropic composites with arbitrary fiber orientation in: Proceedings of the 2nd CIRP Conference on Composite Material Parts Manufacturing (CCMPM 2019), Sheffield, United Kingdom, Procedia CIRP 85 (2019): 2-7, 2019 doi.org/10.1016/j.procir.2019.09.019
Rana, P.; Hintze, W.; Zielasko, W.; Schuster, T.: Orthogonal Turning Simulations for Casted Steel Alloy Using Mesh Free Methods in: Wulfsberg, J. P.; Hintze, W.; Behrens, B.-A. (Eds.): Production at the leading edge of technology, Proceedings of the 9th Congress of the German Academic Association for Production Technology (WGP), Hamburg, September 30 - October 2, Springer Vieweg Verlag, 2019, S. 337-346, ISBN 978-3-662-60417-5
Wulfsberg, J. P.; Hintze, W.; Behrens, B.-A. (Eds.): Production at the leading edge of technology Proceedings of the 9th Congress of the German Academic Association for Production Technology (WGP), Hamburg, September 30 - October 2, Springer Vieweg Verlag, 2019, ISBN 978-3-662-60417-5
Cordes, M.: Modellierung von Bahngenauigkeit und dynamischer Stabilität beim robotergeführten Fräsen Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Band 39, Hamburg, 2019, ISSN 1613-8244
Susemihl, H.: Mobile Robotersysteme zur Zerspanung von Großstrukturen in der Flugzeugproduktion Dissertation, erschienen in: Hintze, W.; Mayer, B.; Wollnack, J.; Niermann, D. (Hrsg.): Forschung für die Produktionstechnik von Morgen, Band 3, Fraunhofer IFAM, Stade, Fraunhofer Verlag, Stuttgart, 2019, ISBN 978-3-8396-1440-2
Hintze, W.; von Wenserski, R.; Möller, C.: Assessment of support structures with regard to their machinability in simultaneous precision machining of SLS Ti6Al4V parts Technical Report, CIRP Winter Meetings, Collaborative Working-Group on Additive Manufacturing, Paris, 2019-02-20
Schulze, B.; Koch, P.; Bonas, J.; Bense, R.; Borrmann, C.; Hintze, W.: Industrial Approaches to Realize a Digital Production in Aviation Industry in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 7th International Workshop on Aircraft System Technologies (AST 2019), February 19 - 20, 2019, Hamburg, Germany Reihe: Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2019, S. 245-254, ISBN 978-3-8440-6470-4
Hintze, W.; Lödding, H.; Friedewald, A.; Mehnen, J.; Romanenko, D.; Möller, C.; Brillinger, C.; Sikorra, J.: Digital Assistance Systems for Smart Drilling Units in Aircraft Structural Assembly in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 7th International Workshop on Aircraft System Technologies (AST 2019), February 19 - 20, 2019, Hamburg, Germany Reihe: Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2019, S. 255-266, ISBN 978-3-8440-6470-4
Brillinger, C.; Susemihl, H.; Ehmke, F.; Staude, T.; Deutmarg, K.; Klemstein, M.; Böhlmann, C.; Hintze, W.; Wollnack, J.: Mobile Laser Trackers for Aircraft Manufacturing: Increasing Accuracy and Productivity of Robotic Applications for Large Parts in: SAE Technical Papers 2019-03-19, ISSN 0096-5170, DOI:10.4271/2019-01-1368
Hintze, W.; Lödding, H.; Friedewald, A.; Mehnen, J.; Romanenko, D.; Sikorra, J.: Digitalisierte Bohrtechnologie für die Strukturmontage Digitised Drilling Technology for the Structure Assembly in: CFK-Valley Stade e.V. (Hrsg.): INNOVATION REPORT, 1-2019, S. 46-47 INNOVATION REPORT, Ausgabe 1-2019 (PDF-Datei, Seite 46)
2018
Hintze, W.; Blühm, M.; Ploog, P.: Laser-Scored-Machining steigert Qualität und reduziert Werkzeugkosten beim Besäumen von Faserverbundbauteilen in: Unter Span - Magazin des Machining Innovations Network (2018), S. 20-21
Hintze, W.; Schötz*, R.; Mehnen, J.; Köttner, L.; Möller, C.: Helical milling of bore holes in Ti6Al4V parts produced by selective laser melting with simultaneous support structure removal in: Denkena, B. (Hrsg.): Procedia Manufacturing of the 18th Machining Innovations Conference for Aerospace Industry - MIC 2018, Hannover, Volume 18 (2018) S. 89-96, Elsevier available online 13 December 2018 doi.org/10.1016/j.promfg.2018.11.012
Hintze, W.; Korves, L.; Blühm, M.; Ploog, P.; Müller, M.: Laser Scored Machining - Prozesssichere Fräsbearbeitung von CFK-Komponenten für die Luftfahrtindustrie 8. IfW-Tagung Bearbeitung von Verbundwerkstoffen, Stuttgart, 29.11.2018
Hintze, W.; von Wenserski, R.: IPMT entwickelt Strategien für die spanende Nachbearbeitung additiver Bauteile in: Hanse-Aerospace Bulletin, 03/2018, S.20-21
Hintze, W.; Steinbach, S.: Grundlagen der Zerspanung von gesintertem Hartmetall Seminar "Hartmetall Fräsen", Vortrag, Soltau, 26.09.2018
Rawal, P.; Brillinger, C.; Böhlmann, C.; Hintze, W.: Sensor based online quality monitoring system for detection of milling defects on CFRP structures (Sensorbasiertes Online-Qualitätsüberwachungssystem zur Detektion von Schäden an CFK-Fräskanten) Deutscher Luft- und Raumfahrtkongress 2018 "Luft- und Raumfahrt – Digitalisierung und Vernetzung", Vortrag, Friedrichshafen, 5. September 2018
Cordes, M.; Hintze, W.; Altintas, Y.: Chatter stability in robotic milling In: Robotics and Computer-Integrated Manufacturing 55 (2019), p. 11–18, Elsevier available online 26 July 2018 doi:10.1016/j.rcim.2018.07.004
Brügmann, F.: Bauteilqualität und Werkzeugverschleiß beim Fräsen von CFK-Gelege unter räumlichen Eingriffsbedingungen Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Band 36, Hamburg, 2018, ISSN 1613-8244
Kothe, S. M.: Spanende Bearbeitung von Faserverbundstrukturen mit Industrierobotern für die Luftfahrt Dissertation, erschienen in: Hintze, W.; Mayer, B.; Wollnack, J.; Niermann, D. (Hrsg.): Forschung für die Produktionstechnik von Morgen, Band 1, Fraunhofer IFAM, Stade, Fraunhofer Verlag, Stuttgart, 2018, ISBN 978-3-8396-1278-1
Hintze, W.; Brügmann, F.; Cordes, M.; Boll, B.: Modeling of Tool Wear in Full Cut Milling of Unidirectional CFRP with Tungsten Carbide Technical Report, CIRP Winter Meetings, CWG Composite Materials Part Manufacturing, Paris, 2018-02-22
Hintze, W.; Clausen, R.; Schütte, C.; Kroll, K.: Evaluation of the Total Cutting Force in Drilling of CFRP - A Novel Experimental Method for the Analysis of the Cutting Mechanism Production Engineering (2018), DOI 10.1007/s11740-018-0807-2
Hintze, W.; Steinbach, S.: Grundlagen der Zerspanung von gesintertem Hartmetall Seminar "Hartmetall Fräsen", Vortrag, Soltau, 07.02.2018
Proes, F.; Eichenseer, C.; Hintze, W.; Schell, N.; Leahy, W.; M'Saoubi, R.; Sattel, S.: In situ analysis of PCBN cutting tool materials during thermo-mechanical loading using synchrotron radiation Production Engineering (2018), DOI 10.1007/s11740-018-0791-6
Hintze, W.; Steinbach, S.; Susemihl, C.; Kähler, F.: HPC-milling of WC-Co cemented carbides with PCD International Journal of Refractory Metals and Hard Materials, Elsevier, 2018 available online 18 December 2017 doi:10.1016/j.ijrmhm.2017.12.019
2017
Möller, C.; Schmidt, H.; Koch, P.; Böhlmann, C.; Kothe, S.; Wollnack, J.; Hintze, W.: Machining of large scaled CFRP-Parts with mobile CNC-based robotic system in aerospace industry in: Denkena, B. (Hrsg.): Procedia Manufacturing of the 17th Machining Innovations Conference for Aerospace Industry - MIC 2017, Hannover, Volume 14 (2017) S. 17-29, Elsevier available online 05 December 2017 doi:10.1016/j.promfg.2017.11.003
Susemihl, H.; Brillinger, C.; Stürmer, S.; Hansen, S.; Böhlmann, C.; Kothe, S.; Wollnack, J.; Hintze, W.: Referencing Strategies for High Accuracy Machining of Large Aircraft Components with Mobile Robotic Systems SAE Technical Paper 2017-01-2166, 2017
Möller, C.; Schmidt, H.; Koch, P.; Böhlmann, C.; Kothe, S.; Wollnack, J.; Hintze, W.: Real Time Pose Control of an Industrial Robotic System for Machining of Large Scale Components in Aerospace Industry Using Laser Tracker System SAE Int. J. Aerosp. 10(2):100-108, 2017
Hintze, W.; Brügmann, F.: Influence of spatial tool inclination on delamination when milling CFRP Journal of Materials Processing Technology available online 26 October 2017 doi:10.1016/j.jmatprotec.2017.10.041
Hintze, W.; Köttner, L.: Curved Circular Cutting - Innovative Trennschleiftechnologie rationalisiert das Besäumen von FVK-Schalenbauteilen Composites Europe 2017, Vortrag, Stuttgart, 21.09.2017
Kothe, S.; Koch, P.; von Stürmer, S. P.; Böhlmann, C.; Hintze, W.: Die Roboter kommen. Roboterbasierte Zerspanungssysteme ergänzen die Werkzeugmaschine in: Unter Span - Magazin des Machining Innovations Network (2017) 2, S. 16-17
Hintze, W.; Brügmann, F.; Köttner, L.; Mehnen, J.: Bearbeitung von FVK-Strukturen mit innovativen Technologien und Produktionssystemen 2. Bremer Faserverbundtage, Vortrag, Bremen, 31.08.-01.09.2017
Hintze, W.; Steinbach, S.; Hertel, C.; Kähler, F.; Mai, T. N.: Machinability and Process Performance in HPC-Milling of Sintered Tungsten Carbide 67th CIRP General Assembly, Technical Report STC C - Cutting, Lugano (Switzerland), August 25th 2017
Hintze, W.; Möller, C.; Schötz, R.: Spanende Nachbearbeitung additiv gefertigter Titanstrukturen der Luftfahrt MIN Workshop "Nachbearbeitung additiv gefertigter Bauteile", Vortrag, Varel, 12./13.07.2017
Hintze, W.; Steinbach, S.; Hertel, C.; Kähler, F.: HPC-Milling of WC-Co cemented carbides with PCD in: Proceedings of the 19th Plansee Seminar, International Conference on Refractory Metals and Hard Materials, May 29 – June 2, 2017, Reutte/Austria
Hintze, W.; Klingelhöller, C.: Analysis and Modeling of Heat Flux into the Tool in Abrasive Circular Cutting of Unidirectional CFRP in: Procedia of the 1st CIRP Conference on Composite Materials Parts Manufacturing (CIRP CCMPM '17), June 8-9, 2017, Karlsruhe, Elsevier, Vol. 66, 2017, S. 210-214, ISSN: 2212-8271 doi:10.1016/j.procir.2017.03.305
Hintze, W.; Brügmann, F.: Influence of Curved Workpiece Contours on Delamination During end Milling of FRP in: Procedia of the 10th Conference on Intelligent Computation in Manufacturing Engineering (CIRP ICME '16), July 20-22, 2016, Ischia, Italy, Elsevier, Vol. 62, 2017, S. 62-67, ISSN: 2212-8271 doi:10.1016/j.procir.2016.06.115
Hintze, W.; Schötz, R.: 3D Druck - Ohne spanende Nachbearbeitung kein funktionsfähiges Bauteil in: Unter Span - Das Magazin des Machining Innovations Network (2017) 1, S. 24-25
Hintze, W.; Köttner, L.: Trennschleifen in einer neuen Dimension - Maschinengeführte 3D Bearbeitung von CFK-Schalenbauteilen mit der Trennscheibe Abrasive Cutting in a new dimension – machine guided 3D processing of CFRP shell components with cutting disk in: CFK-Valley Stade e.V. (Hrsg.): INNOVATION REPORT, 1-2017, S. 30-31 INNOVATION REPORT, Ausgabe 1-2017 (PDF-Datei, Seite 30)
Geis, T.: Bearbeitungsstrategien zur Zerspanung von Faser-Verbund-Honeycomb-Sandwich Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr.33, Hamburg, 2017, ISSN 1613-8244
Hintze, W.; Brügmann, F.; Cordes, M.; Mehnen, J.: Modellierung von Delaminationsphänomenen bei der Zerspanung langfaserverstärkter Faserverbundwerkstoffe In: Biermann, D. (Hrsg.): Spanende Fertigung. Prozesse, Innovationen, Werkstoffe. Vulkan-Verlag, Essen, 2017, S. 65–78, ISBN 978-3-8027-2989-8
Valencia, D.; Wollnack, J.: Identification of the Geometrical Relationships of Sensor, Tool and Actuator Flange via Defined Machine Movements for Fully Automated Bracket Installation in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 6th International Workshop on Aircraft System Technologies (AST 2017), February 21 - 22, 2017, Hamburg, Germany Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2017, S. 337-346, ISBN 978-3-8440-5086-8
Kothe, S.; von Stürmer, S. P.; Koch, P.; Böhlmann, C.; Hintze, W.: Accuracy Analysis and Optimization of Industrial Robots for Aerospace Production in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 6th International Workshop on Aircraft System Technologies (AST 2017), February 21 - 22, 2017, Hamburg, Germany Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2017, S. 347-353, ISBN 978-3-8440-5086-8
Schmick, F.; Rao, S.; Wollnack, J.: Adaptive Robot Trajectory Planning for the Automated Bonding of Large CFRP Structures in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 6th International Workshop on Aircraft System Technologies (AST 2017), February 21 - 22, 2017, Hamburg, Germany Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2017, S. 355-364, ISBN 978-3-8440-5086-8
Hintze, W.; Möller, C.; Schötz, R.: Finish Machining of Titanium Components - Challenges of New Process Chains and Recent Alloys in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 6th International Workshop on Aircraft System Technologies (AST 2017), February 21 - 22, 2017, Hamburg, Germany Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2017, S. 397-407, ISBN 978-3-8440-5086-8
2016
Hintze, W.; Brügmann, F.; Cordes, M.: Entwicklung und Einsatzverhalten von Hartmetallwerkzeugen zum Bohren und Fräsen von Kohlenstofffaserverstärktem Kunststoff (CFK) In: Tagungsband zu "35. Hagener Symposium Pulvermetallurgie - Zerspanung von und mit pulvermetallurgischen Werkstoffen", 24.-25. November 2016, Hagen, S. 213-230, ISBN 978-3-946537-32-8
Hintze, W.; Rosenthal, O.: Bearbeitungsgerechte Auswahl von Werkzeugspannsystemen für Schaftwerkzeuge in: Unter Span - Das Magazin des Machining Innovations Network (2016) 2, S. 22
Hintze, W.; Cordes, M.; Geis, T.; Blühm, M.; Emmelmann, C.; Canisius, M.: Laser Scored Machining of Fiber Reinforced Plastics to Prevent Delamination in: Denkena, B.; Aoyama, T.; Arrazola, P.-J.; Altintas, Y.; Lucca, D. A. (Hrsg.): Procedia Manufacturing of the 16th Machining Innovations Conference for Aerospace Industry - MIC 2016, Hannover, Volume 6 (2016) S. 1-8, Elsevier, available online 18 November 2016, doi:10.1016/j.promfg.2016.11.001
Susemihl, H.; Möller, C.; Kothe, S.; Schmidt, H.; Shah, N.; Brillinger, C.; Wollnack, J.; Hintze, W.: High Accuracy Mobile Robotic System for Machining of Large Aircraft Components SAE Int. J. Aerosp. 9(2):2016, doi:10.4271/2016-01-2139
Kothe, S.; Stürmer, S.; Schmidt, H.; Böhlmann, C.; Wollnack, J.; Hintze, W.: Accuracy Analysis and Error Source Identification for Optimization of Robot based Machining Systems for Aerospace Production SAE Technical Paper 2016-01-2137, 2016, doi:10.4271/2016-01-2137
Hintze, W.; Klingelhöller, C.; Köttner, L.: Curved Circular Cutting of Spherical CFRP Structures - Kinematics, Tool Engagement and Edge Quality CIRP General Assembly, Technical Report STC C, Guimaraes, Portugal, August 25th 2016
Cordes, M.; Hintze, W.: Offline simulation of path deviation due to joint compliance and hysteresis for robot machining in: The International Journal of Advanced Manufacturing Technology (2017) 90, pp. 1075-1083, available online 17 September 2016, doi:10.1007/s00170-016-9461-z
Hintze, W.; Brügmann, F.: Influence of curved workpiece contours on delamination during end milling of FRP "CIRP ICME '16 - 10th CIRP Conference on Intelligent Computation in Manufacturing Engineering", Vortrag, Ischia, Italien, 20.-22.07.2016
Böhlmann, C.; Kothe, S.; Susemihl, H.; Hintze, W.: Produktion mobilisieren - Mobiles Robotersystem zur mechanischen Bearbeitung von Großstrukturen in: Unter Span - Das Magazin des Machining Innovations Network (2016) 1, S. 16
Klingelhöller, C.: Trennschleifen von CFK-Schalenbauteilen mit räumlich gekrümmten Konturen Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 30, Hamburg, 2016, ISSN 1613-8244
Griefahn, D.: Geometrieprüfung innerer Strukturen von Faserverbund-Sandwichbauteilen Dissertation, erschienen in: Hintze, W.; Wollnack, J.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 28, Hamburg, 2015, ISSN 1613-8244
Hintze, W.; Steinbach, S.: Direktzerspanung von gesintertem Hartmetall: Herausforderungen und Perspektiven Makino Werkzeug- & Formenbauforum (Die & Mould Forum), Kirchheim unter Teck, 24. - 25. November 2015
Hintze, W.; Klingelhöller, C.; Griefahn, D.; Geis, T.: Faserverbundbauteile nacharbeitsfrei besäumen durch Laser-Scored-Machining (LSM) Trimming fibre composite components without rework by Laser-Scored-Machining (LSM) in: CFK-Valley Stade e.V. (Hrsg.): INNOVATION REPORT, 1-2015, S. 34-35 INNOVATION REPORT, Ausgabe 8, 1-2015 (PDF-Datei, Seite 34)
Hintze, W.; Körkel, G. K.: Zerspanbarkeit von Faserkunststoffverbunden - Neue Erkenntnisse durch Grundlagenuntersuchungen in: Unter Span - Das Magazin des Machining Innovations Network (2015) 2, S. 25-26
Dose, F.: Methode zur wissensbasierten Prozessentwicklung - Ein Ansatz für die Berücksichtigung sich wandelnder Teilsysteme beim Bohren von Schichtverbunden Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 26, Hamburg, 2015, ISSN 1613-8244
Hintze, W.; Klingelhöller, C.: 3D-Trennschleifen zum Besäumen räumlich gekrümmter CFK-Bauteile 1st International Composites Congress, Stuttgart, 21.-22. September 2015
Hintze, W.; Möller, C.; Steinbach, S.: Fräsen von gesintertem Hartmetall in: Unter Span - Das Magazin des Machining Innovations Network (2015) 1, S. 19 Unter Span 01/2015 (S. 19)
Hintze, W.; Cordes, M.; Susemihl, H.: Stand und aktuelle Entwicklungen der Zerspanung mit Industrierobotern MIN-Workshop Alternative Fertigungstechnologien, Varel, 24.03.2015
Körkel, G. K.: Zerspanbarkeitsbewertung von Faserverbundkunststoffen bei der Fräsbearbeitung dünnwandiger Bauteile in der Großserie Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 24, Hamburg, 2015, ISSN 1613-8244
Lay, M.; Leahy, W.; O'Malley, D.; Geis, T.; Hintze, W.: Trimming and Slotting of Carbon Fiber Reinforced Polymer (CFRP) with PCD End Mills in: Proceedings of INTERTECH 2015, May 19 - 20, 2015, Indianapolis, USA
Hintze, W.: Entwicklung und Einsatz von Präzisionswerkzeugen zum Bohren und Fräsen von CFK 6. Wernesgrüner Werkzeugsymposium, 11.-13.03.2015
Möller, C.: Neue Ansätze zur Präzisionsbearbeitung von Leichtbauwerkstoffen, 5. ordentliche Mitgliederversammlung "Machining Innovation Network", Vortrag, Varel, 25.02.2015
Hintze, W.; Brügmann, F.: Endmilling of Recent CFRP Materials with Cemented Carbide and Diamond Tools - Analysis of Process; Tool Wear and Quality in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 5th International Workshop on Aircraft System Technologies (AST 2015), February 24 - 25, 2015, Hamburg, Germany Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2015, S. 373-382, ISBN 978-3-8440-3319-9
Hintze, W.; Eichenseer, C.: Analysis of Phase-dependent Strains and Stress in Mixed Ceramics under Thermo-mechanical Load using Synchrotron Radiation Technical Report, CIRP Winter Meetings, STC Cutting, Paris, 2015-02-19
Eichenseer, C.; Hintze, W.; Sattel, S.: Untersuchung des Schneidstoffverhaltens "in situ" - Innovative Messmethode detektiert Spannungen in: VDI-Z 157(2015) 1/2, Springer-VDI-Verlag, Düsseldorf, 2015, S. 44-47
Hintze, W.; Cordes, M.; Körkel, G.: Influence of weave structure on delamination when milling CFRP in: Journal of Materials Processing Technology 216 (2015), S. 199-205, available online 21 September 2014, doi:10.1016/j.jmatprotec.2014.09.004
2014
Hintze, W.; Klingelhöller, C.; Langhof, O.: Curved sawing of thin lightweight components in: Journal of Production Engineering Research and Development, available online 27 November 2014, doi:10.1007/s11740-014-0587-2
Eichenseer, C.: Beschichtung, thermomechanische Charakterisierung und Spannungsanalyse von Schneidkeramik Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 22, Hamburg, 2014, ISSN 1613-8244
Hintze, W.; Cordes, M.: Robotergeführtes Fräsen von Leichtbauwerkstoffen in: Unter Span - Das Magazin des Machining Innovations Network (2014) 2, S. 27
Körkel, G.; Hintze, W.; Polley, W.; Zielasko, W.: Machinability of fiber-reinforced plastics - An integral approach for large-scale production in: Proceedings of the 8th International CFK-Valley Stade Convention 2014, June 24-25, 2014, Stade, Germany, S. 116-122
Geis, T.; Klingelhöller, C.; Hintze, W.: Constant Depth Scoring of Fibre Reinforced Plastic Structures to Prevent Delamination in: Procedia of the 6th CIRP International Conference on High Performance Cutting (HPC2014), June 23-25, 2014, Berkeley, USA, Elsevier, Vol. 14, 2014, S. 205-210 doi:10.1016/j.procir.2014.03.103
Griefahn, D.; Wollnack, J.; Hintze, W.: Principal component analysis for fast and automated thermographic inspection of internal structures in sandwich parts in: Journal of Sensors and Sensor Systems, 3, pp. 105-111, 2014 doi:10.5194/jsss-3-105-2014
Hintze, W.: Neue Ansätze zur wirtschaftlichen Präzisionsbearbeitung von CFK-Strukturen in: Bleicher, F.; Lammer, K. (Hrsg.): Industrie 4.0 – die intelligente Fabrik der Zukunft, Tagungsband, 2. Wiener Produktionstechnik Kongress 07.-08.05.2014, Klein Publishing, Wien, Österreich, 2014, S. 131-140, ISBN 978-3-903015-00-5
Hintze, W.; Kothe, S.; Susemihl, H.: Flexible Präzisionsbearbeitung von CFK-Großstrukturen mit Industrierobotern in: Ingenieurspiegel 1/2014, Public Verlagsgesellschaft, Bingen, S. 24-26
Eichenseer, C.; Hartig, C.; Schell, N.; Hintze, W.: In situ determination of internal stresses in mixed ceramic cutting tools during friction testing using synchrotron ratiation in: Journal of Production Engineering Research and Development, 2014 doi:10.1007/s11740-014-0535-1
Schütte, C.: Bohren und Hobeln von kohlenstofffaserverstärkten Kunststoffen unter besonderer Berücksichtigung der Schneide-Faser-Lage Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 20, Hamburg, 2014, ISSN 1613-8244
Hintze, W.; Clausen, R.; Schütte, C.: The Cutting Force Vector in Drilling of Unidirectional CFRP - A New Approach for Process Analysis Technical Report, CIRP Paris January Meetings, STC Cutting, Paris, 2014-01-23
2013
Hintze, W.; Steinbach, S.: Präzisionsbohren von CFK und Schichtverbunden in: CFK-Valley Stade e.V. (Hrsg.): INNOVATION REPORT, 2-2013, S. 28-29. INNOVATION REPORT, Ausgabe 2, 2-2013 (S. 28)
Hintze, W.; Schütte, C.; Steinbach, S.: Influence of the Fiber Cutting Angle on Work Piece Temperature in Drilling of Unidirectional CFRP in: Denkena, B. (Hrsg.): Lecture Notes in Production Engineering: New Production Technologies in Aerospace Industry, Proceedings of the 4th Machining Innovations Conference, Hannover, September 2013, Springer, S. 137-143, doi:10.1007/978-3-319-01964-2_19
Freising, M.; Kothe, S.; Rott, M.; Susemihl, H.; Hintze, W.: Increasing Accuracy of Industrial Robots in Machining of Carbon Fibre Reinforced Plastics in: Denkena, B. (Hrsg.): Lecture Notes in Production Engineering: New Production Technologies in Aerospace Industry, Proceedings of the 4th Machining Innovations Conference, Hannover, September 2013 Springer ISBN 978-3-319-01963-5
Hintze, W.; Wollnack, J.; Griefahn, D.: Principal Component Analysis for Fast and Automated Thermographic Inspection of Internal Structures in Sandwich Parts in: Schmitt, R.; Bosse, H. (Hrsg.): ISMTII 2013: Metrology - Master Global Challenges - "The 11th International Symposium on Measurement Technology and Intelligent Instruments", July 1st - July 5th, 2013, Aachen Apprimus Verlag, RWTH, Aachen, Germany, 2013 ISBN 978-3-86359-138-0
Hintze, W.; Hartmann, D.: Modeling of delamination during milling of unidirectional CFRP in: Procedia of the 14th CIRP Conference on Modeling of Machining Operations (CIRP CMMO 2013), Juni 13 - 14, 2013, Turin, Italien, Elsevier, Vol. 8, S. 443-448, doi:10.1016/j.procir.2013.06.131
Hintze, W.; Hartung, F.; Kawala, D.; Klingelhöller, C.; Olesch, M.: Efficient and Reliable Grinding of Landing Gear Parts in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 4th International Workshop on Aircraft System Technologies (AST 2013), April 23 - 24, 2013, Hamburg, Germany Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2013, S. 345-354, ISBN 978-3-8440-1850-9
Hintze, W.; Möller, C.: Hochleistungs-Schlichtfräsen dünnwandiger Titanbauteile Unter Span - Das Magazin des Machining Innovations Network (2013) 1, S. 13
Hintze, W.: Präzisionsbearbeitung von CFK-Strukturen im Mobilitätssektor - Herausforderungen und Lösungen In: Tagungsband zu "19. Nationales Symposium SAMPE Deutschland e. V. - Faserverbundwerkstoffe in der Energiewende", 27.-28. Februar 2013, Hamburg, S. 62-64, ISBN 978-3-941492-58-5
2012
Eichenseer, C.; Wittmann, I.; Hartig, C.; Schell, N.; Hintze, W.: In situ measurement of lattice strains in mixed ceramics under static thermal and mechanical loads (PDF), HASYLAB Annual Reports 2012
Hartmann, D.: Delamination an Bauteilkanten beim Umrissfräsen kohlenstofffaserverstärkter Kunststoffe Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 17, Hamburg, 2012
Eichenseer, C.; Wittmann, I.; Hartig, C.; Schneider, G. A.; Schell, N.; Hintze, W.: In situ measurement of lattice strains in mixed ceramic cutting tools under thermal and mechanical loads using synchrotron radiation In: Production Engineering - Research and Development 7(2013)2-3, 01 Apr 2013, S. 283-289 available online 02 November 2012, doi:10.1007/s11740-012-0426-2
Hintze, W.; Kothe, S.; Niermann, D.; Wollnack, J.; Borrmann, C.: Reliable Machining of CFRP Components with Industrial Robots ISCM 2012, 6th International Symposium on "Manufacturing Technology for Composite Aircraft Structures", 24.-25. October 2012, DLR Stade
Hintze, W.; Hartmann, D.; Schütte, C.; Goßmann, U.: Mechanisms and Avoidance of Delamination in Edge Milling of CFRP Technical Report, CIRP General Assembly, STC Cutting, Hong Kong, 2012-08-24
Hintze, W.; Hartmann, D.; Schubert, U.: Stirnfräsen von CFK zur Fügeflächenherstellung und Reparaturvorbereitung in: ZWF (2012) 6, Carl Hanser Verlag, München, S. 462-466 (http://www.zwf-online.de/ZW110775)
Hintze, W.; Kober, H.; Kothe, S.-M.; Ograbisz, P.; Schütte, C.: Temperaturen beim Fräsen von Composites beherrschen - Mit neuen Analysemethoden zu optimalen Prozessen Unter Span - Das Magazin des Machining Innovations Network (2012) 1, S. 10-11 (PDF)
Hintze, W.; Hartmann, D.; Goßmann, U.: Kantenqualiät beim Umrissfräsen von CFK verbessern - Modellgestützte Delaminationsanalyse erlaubt angepasste Bearbeitungsstrategien in: VDI-Z 154(2012) 1/2, Springer-VDI-Verlag, Düsseldorf, 2012, S. 24-27
2011
Hintze, W.; Kothe, S.-M.; Kober, H.: Investigations on process temperature in machining of CFRP composites in: Proceedings of the 6th International Conference "Supply on the wings", AIRTEC 2011, 02.-04.11.2011, Frankfurt (Main), 2011
Hintze, W.; Hartmann, D.; Schütte, C.: Occurrence and propagation of delamination during the machining of carbon fibre reinforced plastics (CFRPs) - An experimental study in: Composites Science and Technology 71(2011)15, 24 Oct 2011, S. 1719-1726 available online 22 August 2011, doi:10.1016/j.compscitech.2011.08.002
Hintze, W.; Möller, C.: Innovation in der Zerspanungstechnologie von Leichtbauwerkstoffen Unter Span - Das Magazin des Machining Innovations Network (2011) 1, S. 19
Frömming, H.: Zerspanung von WC-Co-Hartmetall im unterbrochenen Schnitt Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 13, Hamburg, 2011
Schütte, C.: Prozesssichere Zerspanung aktueller CFK-Werkstoffe in: Tagungsband des OTTI-Fachforum "Neue Werkstoffe wirtschaftlich zerspanen- Werkzeuge, Fertigungsprozesse, Problemlösungen, Perspektiven", 06.-07. Juni 2011, OTTI e. V., Regensburg, 2011, S. 195-215
Schütte, C.; Dose, F.: Wirtschaftliche und prozesssichere Bohrbearbeitung von CFK in: lightweightdesign 2/2011, Verlag Vieweg+Teubner, Wiesbaden, 2011, S. 50-57, ISSN 1865-4819
Eichenseer, C.; Wittmann, I.; Schneider, G. A.; Hartig, C.; Hintze, W.: Stress-strain evaluation of mixed ceramics under thermal and mechanical loads using x-ray diffraction (PDF), HASYLAB Annual Reports 2011
Hintze, W.; Wollnack, J.; Backhaus, S.; Kothe, S.-M.; Neuendorf, M.: Process Monitoring for Reliable Machining of CFRP Structures in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 3rd International Workshop on Aircraft System Technologies (AST 2011), March 31 - April 01, 2011, Hamburg, Germany Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2011, S. 413-424, ISBN 978-3-8322-9904-0
2010
Eichenseer, C.; Hintze, W.; Schneider, G. A.; Röhlsberger, R.; Glaser, L.; Schell, N.: X-ray characterization of a TiAlN-coating on a mixed ceramic substrate with a resolution of a few microns (PDF), HASYLAB Annual Reports 2010
Hintze, W.; Dose, F.; Hartmann, D.; Schütte, C.: Assessment of surface integrity of machined CFRP - Methods and Results in: Proceedings of the 5rd International Conference "Supply on the wings", AIRTEC 2010, 02.-04.11.2010, Frankfurt (Main), 2010, ISBN 978-3-942939-00-3
Schütte, C.: Prozesssichere Zerspanung aktueller CFK-Werkstoffe in: Tagungsband des OTTI-Fachforum "Neue Werkstoffe wirtschaftlich zerspanen- Werkzeuge, Fertigungsprozesse, Problemlösungen, Perspektiven", 09.-10. Juni 2010, OTTI e. V., Regensburg, 2010, S. 259-275
Niermann, D.; Hintze, W.; Wollnack, J.: The Process Chain of CFRP XXL-Structures in CFK Nord in: Proceedings of the 4th International CFK-Valley Stade Convention 2010, June 15-16, 2010, Stade, Germany, S. 16-19
Kindler, J.: Werkstückqualität und Standzeitoptimierung von Zerspanwerkzeugen bei der Umrissbearbeitung von kohlenstofffaserverstärkten Kunststoffen Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 12, Hamburg, 2010
Sellmer, D.: Untersuchungen zur Verbesserung des Arbeitsergebnisses beim Vollbohren unter besonderer Berücksichtigung der Prozesskräfte und der Spanbildung Dissertation, erschienen in: Hintze, W.; Lödding, H.; Nedeß, Chr. (Hrsg.): Wissen schafft Innovation, Nr. 10, Hamburg, 2010
2009
Hintze, W.; Frömming, H.; Dethlefs, A.: Influence of machining with defined cutting edge on the subsurface microstructure of WC-Co parts in: International Journal of Refractory Metals and Hard Materials 28(2010)2 S.274-279, available online 3 November 2009, DOI:10.1016/j.ijrmhm.2009.10.012
Hintze, W.; Frömming, H.: Upgrading the Toolbox of Machining Cemented Tungsten Carbides in: Sigl, L.S.; Rödhammer, P.; Wildner, H. (eds.): Proceedings of the 17th Plansee Seminar, International Conference on High Performance PM Materials, May 25 - 29, 2009, Reutte/Austria
Gotsch, F.: Untersuchungen zum Zerspanverhalten von Elastomerschäumen mit dem Ziel einer wirtschaftlichen Fertigung von Feder-Dämpfer-Bauteilen Dissertation, erschienen in: Nedeß, Chr.; Hintze, W. (Hrsg.): Wissen schafft Innovation, Nr. 8, Hamburg, 2009
Hintze, W.; Friedewald, A.; Dose, F.: Innovative Process Planning and Diagnosis by Integrated Knowledge Management in: von Estorff, O.; Thielecke, F. (Hrsg.): Proceedings of the 2nd International Workshop on Aircraft System Technologies (AST 2009), March 26-27, 2009, Hamburg, Germany Berichte aus der Luft- und Raumfahrttechnik, Shaker Verlag, Aachen, 2009, S. 199-210, ISBN 978-3-8322-8071-0
Möller, C.: Untersuchungen zum Drehen von gesinterten WC-Co-Hartmetallwalzringen Dissertation, erschienen in: Nedeß, Chr.; Hintze, W. (Hrsg.): Wissen schafft Innovation, Nr. 7, Hamburg, 2009
2008
Hintze, W.; Hartmann, D.; Schütte, C.; Schwerdt, M.: Wet machining of CFRP in: Proceedings of the 3rd International Conference "Supply on the wings", AIRTEC 2008, 11.-13.11.2008, Frankfurt (Main), available on CD only
Hintze, W.; Möller, C.: Automatisierte Erzeugung spiegelnder Oberflächen durch 3D-Schleifen Sachbericht KF0202201PK5, Pro Inno II, 2008
Bhattacharya, A. K.; Zimmermann, K.; Schneider, G. A.; Hintze, W.: Influence of Surface Modification on the Cutting Performance of Reaction-Sintered Al2O3-TiOC Ceramics in: Journal of the American Ceramic Society 91(2008)9, S. 2982-2986 DOI:10.1111/j.1551-2916.2008.02559.x
2007
Hintze, W.; Dose, F.; Hartmann, D.; Santos Quiroz, S.; Schwerdt, M.: Cutting, abrasive and laser technologies for CFRP machining: state of the art and future trends in: Proceedings of the 2nd International Conference "Supply on the wings", AIRTEC 2007, 24.-25.10.2007, Frankfurt (Main), available on CD only
Püschel, A.: Randzonenmodifikation aluminothermisch hergestellter Mischkeramiken zur Hartbearbeitung Dissertation, erschienen in: Berichte aus der Materialwissenschaft, Shaker, Aachen, 2007
Zimmermann, K.; Schneider, G. A.; Bhattacharya, A. K.; Hintze, W.: Surface Modification of Al2O3/TiC Cutting Ceramics in: Journal of the American Ceramic Society 90(2007)12, S. 3773-3778 DOI:10.1111/j.1551-2916.2007.02039.x
Hintze, W.; Hartmann, D.; Schwerdt, M.: Machining of CFRP in: Proceedings of the 1st International CFK-Valley Stade Convention 2007, June 13-14, 2007, Stade, Germany, S. 53-57
Hintze, W.; Clausen, R.; Hartmann, D.; Kindler, J.; Santos, S.; Schwerdt, M.; Stöver, E.: Precision of machined CFRP The challenge of dimensional accuracy in: Proceedings of the 1st International Workshop on Aircraft System Technologies (AST 2007), March 29-30, 2007, Hamburg, Germany Shaker Verlag Aachen, 2007, S. 361-374
Hintze, W.; Frömming, H.: Schlichtfräsen eröffnet neue Einsatzbereiche Grundlagenuntersuchungen zum Fräsen von gesintertem Hartmetall WB Werkstatt + Betrieb 03/2007, S. 63-67
2006
Hintze, W.; Hartmann, D.; Kindler, J.; Stöver, E.: High Productivity Cutting of CFRP Composite Structures: Workpiece Quality and Tool Wear in: Proceedings of the 1st International Conference "Supply on the wings", AIRTEC 2006, 18.-19.10.2006, Frankfurt (Main), available on CD only
Hintze, W.; Eglins, F.: Automatisierte Erzeugung spiegelnder Oberflächen durch 3D-Schleifen Zwischenbericht KF0202201PK5, Pro Inno II, 2006
Swiostek, J.; Bober, J.; Blawert, C.; Letzig, D.; Hintze, W.; Kainer, K. U.: Die forging of commercial and modified magnesium alloys 7th International Conference on Magnesium Alloys and their Applications, Dresden, 06.-09.11.2006
Hintze, W.; Clausen, R.; Santos Quiroz, S.; Schwerdt, M.: Wirtschaftliche Zerspanung von Leichtbaustrukturen durch den Einsatz innovativer Hartmetallschneidstoffe und Diamantbeschichtungen Congress Intelligente Leichtbau Systeme (ILS) 2006, Hannover, 05./06.09.2006
Hintze, W.; Frömming, H.; Gotsch, F.: Spanende Bearbeitung von Elastomerschäumen Analyse der reversiblen Verformungen und der Zerspankraft beim Drehen kompressibler PUR-Schäume wt Werkstattstechnik online 96(2006)9, S. 662-668
Hintze, W.; Möller, C.: Randzonenuntersuchung an gedrehten Hartmetallbauteilen in: Industrie Diamanten Rundschau 40(2006)II, S. 48-55
2005
Hintze, W.; Eglins, F.: Entwicklung eines neuen Verfahrens zur maschinellen Erzeugung von Oberflächen mit höchster Güte Abschlussbericht Investitions- und Förderbank Niedersachsen, 2005
Joswig, D.: Untersuchung zum Zerspanverhalten weicher Elastomerwerkstoffe Dissertation, erschienen in: Nedeß, Chr.; Hintze, W. (Hrsg.): Wissen schafft Innovation, Nr. 3, Hamburg, 2005
Clausen, R.; Hintze, W.; Stöver, E.: Glare - ein neuer Werkstoff im Flugzeugbau Grundlagen der Bohrbearbeitung in: Zeitschrift für wirtschaftlichen Fabrikbetrieb 100(2005)3, S. 111-116
2004
Hintze, W.; Joswig, D.; Gotsch, F.: Spanende Fertigung von Elastomerdichtungen in: Berger, K.-F.; Kiefer, S. (Hrsg.): Jahrbuch Dichtungstechnik 2005, Hüthig, Heidelberg, 2004, S. 321-326, ISBN 3-7785-2942-0
Hintze, W.; Gotsch, F.; Möller, C.; Püschel, A.; Santos Quiroz, S.; Stöver, E.: Manche mögen's nicht so heiß - Thermische Wechselwirkungen beim Trockenbohren von Leichtbaustrukturen in: Maschinenmarkt 110(2004)37, S. 78-83
Hintze, W.; Möller, C.: Drehtechnologie für Hartmetallwalzen 74. Tagung der Arbeitsgemeinschaft Internationaler Kalibreure u. Walzwerksingenieure (AIKW), Straßburg, September 2004
Hintze, W.; Joswig, D.; Gotsch, F.: Mechanische Grundlagen der Zerspanung von Elastomerdichtungen Tagungsband zu "V. Hamburger Dichtungstechnisches Kolloquium - Dynamische Dichtungen", Radialwellendichtringe, TUHH, Hamburg, 03./04.06.2004
2003
Hintze, W.; Schneider, G. A.; Püschel, A.: Mikromechanische Bewertung aluminothermisch hergestellter Schneidstoffe Arbeitsbericht 2003 zum Teilprojekt D4 des Sonderforschungsbereiches 371, TUHH, 2003
Hintze, W.: Forschen an den Grenzen der Zerspanbarkeit TUHH-Spektrum (2003) 2
Hintze, W.; Schneider, G. A.; Püschel, A.: Reaktionsgesinterte Mischkeramiken zur Hartbearbeitung in: VDI-Z Spezial Werkzeuge II (2003), S. 26-30
Hintze, W.; Nedeß, Chr.; Möller, C.: Auf die harte Tour CVD-Dickschichtdiamant verringert den Verschleiß und die Zerspankräfte in der Hartmetallbearbeitung in: Maschinenmarkt 109(2003)25, S. 26-30
Hintze, W.; Clausen, R.; Stöver, E.; Plucinski, M.: Bohren für den A380 Werkzeug- und Prozessentwicklung im Team in: TUHH SPEKTRUM - Special Luftfahrtforschung, II/2003, S. 26-27
Hintze, W.; Santos Quiroz, S.; Kerse, N.: Concurrent Engineering beim Airbus A380 Planung manueller Montagearbeitsplätze mit Virtual Reality in: TUHH SPEKTRUM - Special Luftfahrtforschung, II/2003, S. 28-29
Hintze, W.; Möller, C.: Heutige Tendenzen der Ultrahartbearbeitung Ein Bericht der TUHH über das Drehen gesinterter Hartmetallwalzen in: Mensch & Technik III/2002, VDI Hamburger Bezirksverband e.V., S. 14-16
Nedeß, Chr.; Hintze, W.; Halver, M.; Möller, C.: Hartdrehen statt Schleifen HSS-Schneidplatten flexibel, wirtschaftlich und funktionsgerecht hart bearbeiten. in: Maschinenmarkt 108(2002)25, S. 38-43
Hintze, W.; Nedeß, Chr.; Joswig, D.: Analyse und Reduktion dynamischer Verformungen beim Drehen von Elastomeren Tagungsband zu "IV. Hamburger Dichtungstechnisches Kolloquium - Dynamische Dichtungen", Radialwellendichtringe, Teil 2, TUHH, Hamburg, 23./24.05.2002
Hintze, W.; Isecke, S.; Joswig, D.: Spritzgießen ade - Fräsen von Elastomerbauteilen in kleinen Stückzahlen ist schnell und flexibel in: Maschinenmarkt 108(2002)11, S. 36-39
2000
Bargel, Frank: Untersuchung der Zerspanbarkeit eines Acrylnitril-Butadien-Elastomers mit dem Ziel der Herstellung von rotationssymmetrischen Dichtungen durch Drehen Dissertation, erschienen in: Fortschritt-Berichte VDI, Reihe 2, Nr. 565, VDI-Verlag, Düsseldorf, 2000
Mohammed, A.; Hagel, H.; Michels, K. P.; Burkhart, G.; Wimmer, K.; Janta, R.; Nedeß, Chr.; Hintze, W.; Rohwer, A.: Optimization of material, geometrical and tribological characteristics for electrode-nipple-joints used in EAF´s Tagungsband EUROCARBON 2000, Berlin, 09.-13.07.2000
Hintze, W.; Nedeß, Chr.; Bargel, F.; Joswig, D.: Technologie der spanenden Bearbeitung von Elastomerdichtungen Tagungsband zu "III. Hamburger Dichtungstechnisches Kolloquium - Dynamische Dichtungen", Radialwellendichtringe, TUHH, Hamburg, 15./16.06.2000
1999
Scherbarth, S.: Der Einfluß der Schneidkeilgeometrie auf das Zerspanverhalten beim Fräsen von Stahlwerkstoffen mit beschichtetem Hartmetall Dissertation, erschienen in: Berichte aus der Fertigungstechnik, Shaker, Aachen, 1999
1998
Gatermann, H.: Reibungseinflüsse auf die Spanbildung beim Drehen Dissertation, erschienen in: Fortschritt-Berichte VDI, Reihe 2, Nr. 497, VDI-Verlag, Düsseldorf, 1998
Nedeß, Chr.; Bargel, F.: Zerspanung entropieelastischer Werkstoffe mit geometrisch bestimmter Schneide in: VDI-Zeitung 140(1998)1/2, S. 28-31
1997
Fang, N.; Wang, M.; Nedeß, Chr.: Development of the new-type indexable with helical rake faces in: Proceedings of the Institution of Mechanical Engineers, Journal of Engineering Manufacture, 1997, Vol 211 Part B, pp. 159-164
Nedeß, Chr.; Gatermann, H.: Einflüsse der Beschichtung auf das Spanbruchverhalten. Hartmetall-Wendeschneidplatten beim Drehen langspanender Werkstoffe in: VDI-Zeitung Special Werkzeuge August '97, S. 40-45
Nedeß, Chr.; Beck, M.: Überwachen des Gewindebohrens Nutzbar machen, was der Mensch hört(e) - Schallanalyse als Grundlage. in: VDI-Zeitung Special Werkzeuge April '97, S. 40-46
1996
Nedeß, Chr.; Pflueg, Chr.: Real-Time Monitoring and Controlling of Chip Form in Turning Processes with Acoustic Emission Using Thin Film Sensors 24th North American Manufacturing Research Conference (NAMRC XXIV), University of Michigan, Ann Arbor/Michigan, USA, 21.-23.05.1996
1994
Günther, U.: Analyse und Optimierung des Einsatzverhaltens von Bohrwerkzeugen mit Hartmetall-Wendeschneidplatten Dissertation, TUHH, 1994
Nedeß, Chr.; Pflueg, Chr.: Chip Form Monitoring in Turning Internal Surfaces with Acoustic Emission using Thin Film Sensors 7th International Conference on Production/Precision Engineering (7th ICPE), Nippon Convention Center (MAKUHARI MESSE), Chiba, Japan, 1994
1992
Schwedler, M.: Dünnschichtsensoren für die Überwachung von Maschinenbauteilen Dissertation, TUHH, 1992
Nedeß, Chr.; Günther, U.: Radial Forces in Short Hole Drilling and their Effects on Drill Performance 20th North American Manufacturing Research Conference (NAMRC XX), Washington State University, Pullman, Washington USA, 20.-22.05.1992
Nedeß, Chr.; Günther, U.: Bohren mit Hartmetall-Wendeplatten-Werkzeugen. Untersuchung der Radialkräfte und ihrer Auswirkungen auf das statische und dynamische Verhalten in: VDI-Zeitung 134(1992)2, S. 49-58
Weindorf, T.: Schwingungen beim Schaftfräsen Modellgestützte Analyse des Schwingungsverhaltens, Ratterursachen, Abhilfemaßnahmen. Dissertation, erschienen in: Fortschritt-Berichte VDI, Reihe 2, Nr. 235, VDI-Verlag, Düsseldorf, 1992
1991
Nedeß, Chr.; Schwedler, M.: Diagnosis of Faults with Thin-film Sensors in a Multiple-Spindle-Drilling-Head 19th North American Manufacturing Research Conference (NAMRC XIX), The University of Missouri-Rolla, Rolla, Missouri USA, 22.-24.05.1991
1990
Nedeß, Chr.; Weindorf, T.: Zur dynamischen Steifigkeit von Werkzeugen und ihrer Aufnahme in: VDI-Zeitung 132(1990)9, S. 110-119
Hintze, W.: Modellgestützte Spanbruchbeurteilung beim Drehen Dissertation, TUHH, 1990
Nedeß, Chr.; Himburg, T.; Holst, G.: Verschleißerfassung bei Schneidplatten mit komplexer Geometrie in: VDI-Zeitung 130(1990)1, S. 51-56
1989
Himburg, T.; Keller, H.: Universelles Rechnerkonzept für die Entwicklung von Überwachungssystemen in: VDI-Zeitung 129(1989)2, S. 71-75
Nedeß, Chr.; Schwedler, M.: Flach und klein - aber fein. Überwachung und Fehlerfrühdiagnose an Maschinenbauteilen mit Sensoren der Dünnschichttechnik in: Maschinenmarkt 95(1989)39, S. 72-79
Nedeß, Chr.; Hintze, W.: Characteristic Parameters of Chip Control in Turning Operations with Indexable Inserts and Three-Dimensionally Shaped Chip Formers Annals of the CIRP Vol. 38/1/1989, CIRP-Konferenz " Manufacturing Technology", Trondheim, Norway, 21.-26.08.1989
1988
Himburg, T.: Die Dynamik des Bohrvorganges als Grundlage eines Überwachungskonzeptes Dissertation, TUHH, 1988
Nedeß, Chr.; Himburg, T.: Drilling Dynamics A Fundamental Base for Drill-Life-Monitoring. 16th North American Manufacturing Research Conference (NAMRC XVI), University of Illinois, Urbana-Champaign, USA, 25.-27.05.1988
1987
Nedeß, Chr.; Hintze, W.; Khanji, M.: Die Hartmetallschneidplatte als Teilkomponente des Werkzeuges in der CIM-Linie in: tz für Metallbearbeitung 81(1987)5, S. 30-35
Nedeß, Chr.; Schwedler, M.: Dünnschichtsensoren zur Diagnose von Maschinenschäden in: VDI-Zeitung 129(1987)9, S. 54-56
Nedeß, Chr.; Hintze, W.: Wirkungsweise eingesinterter Spanformstufen Technologische Grundlagen für die Schneidplattenauswahl und -konstruktion in: VDI-Zeitung 129(1987)10, S. 106-112
1986
Nedeß, Chr.; Himburg, T.: Automatisierte Überwachung des Bohrens Dynamischer Bearbeitungsprozeß als Signalquelle in: VDI-Zeitung 128(1986)17, S. 651-657
Nedeß, Chr.; Himburg, T.; Schwedler, M.: Stabilitätsverhalten von Innendrehwerkzeugen in: VDI-Zeitung 128(1986)11, S. 409-414
Nedeß, Chr.: Werkzeuge in der CIM-Linie in. CIM-Praxis 09/1986, S. 62-66
Nedeß, Chr.; Hintze, W.: Untersuchung der Spanform beim Drehen mit Hilfe der Fotografie in: Yashica/Contax News Nr. 13, 4/86
1984
Nedeß, Chr.: Schnittwertoptimierung bei teilausgelasteten Fertigungssystemen in: tz für Metallbearbeitung 78(1984)12, S. 49-51